mailtrevorcowell.co.ukJul 13, 2026 I got the car out of it's Carcoon and into the yard and was greeted with a box of neutrals, fearing the worst we remove the front cover and was greeted with this snapped lever ! I was able to weld it on there and then. Looking at it it's a big job to replace so am in the process of making a splint. I can post a pic if anyone cares to view the "repair"
Where did you place the earth lead when you did the welding?
Yes I'm interested in seeing the pictures.
I am also wondering why it broke in the first place?
Maybe there are other problems that caused it to break that needs sorting out?
The main vacuum cylinder exerts quite a bit of force, maybe it was a fatigue failure?
However I have never heard of that happening to the gear lever before.
Sorry to say this but welding this piece is a very hard job because the lever is cast iron. As Terry mentioned it's a good idea to find out why this broke. There is a lot of work ahead of who every attempts to replace this lever. The front of the transmission MUST come off completely so the lever can be removed n replaced. there is an oil pump in this mix too known as a grease pump. Then at the bottom is a stack of shims but you wont be removing those. They shim the differential pinion shaft to the ring gear.
the club sells a fine complete transmission book telling you everything you need to know about the part and much more. It costs $40.00 and worth ten times that...
Gary Parsons
Gary ParsonsJul 14, 2026 Sorry to say this but welding this piece is a very hard job because the lever is cast iron. As Terry mentioned it's a good idea to find out why this broke. There is a lot of work ahead of who every attempts to replace this lever. The front of the transmission MUST come off completely so the lever can be removed n replaced. there is an oil pump in this mix too known as a grease pump. Then at the bottom is a stack of shims but you wont be removing those. They shim the differential pinion shaft to the ring gear.
the club sells a fine complete transmission book telling you everything you need to know about the part and much more. It costs $40.00 and worth ten times that...
Gary Parsons
Gary, I think you will find the lever is made out of cast steel and not cast iron.
The critical point is where the earth lead is attached. Trevor certainly does not want stray currents going through gears or bearings.
Terry that is a possibility but touching it to a grinding wheel and observing the sparks is about the best way to know for sure. But to weld this I feel it would be better to just replace it but as you posted finding out why it broke is the better idea. A good machine shop can fabricate a new one from any material you want. It has three drilled holes with one of them threaded on half. One with a broach keyway in it and one just drilled thru. The geometry becomes the important thing. I really have never seen one that was broken like this either.
Gary Parsons
The case with the gear selector cross shaft and "broken" lever can be removed from the gearbox without removing the oil pump which is lower down.
The Dog Bone inside the LHS of the case is held in place with a tapered pin which has to be knocked out.
It is a fairly straight forward job to remove the case.
It will also give you an opportunity to see if the Dog Bone was asseb]mbled the correct way.
Welding the broken lever back in place is a job that will get you home, however it is best to do the job properly after discovering why it happend in the first place.
It will also give you the opportunity to check for wear in the cross shaft keyways. Any slope there can lead to major gear selection problems with loss of syncronization.

Terry CockerellJul 14, 2026 The case with the gear selector cross shaft and "broken" lever can be removed from the gearbox without removing the oil pump which is lower down.
The Dog Bone inside the LHS of the case is held in place with a tapered pin which has to be knocked out.
It is a fairly straight forward job to remove the case.
It will also give you an opportunity to see if the Dog Bone was asseb]mbled the correct way.
Welding the broken lever back in place is a job that will get you home, however it is best to do the job properly after discovering why it happend in the first place.
It will also give you the opportunity to check for wear in the cross shaft keyways. Any slope there can lead to major gear selection problems with loss of syncronization.
Terry I'm amazed how your Cord library always comes to the rescue or others like myself. This picture explains far more than even I could post. I suspect a 3D printer can make this quicker and easier than a machine shop. I know if I had a Bridgeport mill in my modest shop I would try making this. Sometimes I really regret retiring from the Southern California Edison machine shop. We had about 2 acres of bully loaded floor space with every type of lathe, mill, welder or grinder available for use. I used that shop on so many of my home projects. I actually had two Ford diesel heads dropped shipped there because it was easier than shipping to my home shop where I had to be there to offload with a forklift due to the size n weight. We had a huge overstocked tool room with every die grinder with so many choices for the burrs in solid Tungsten or any other style. The TIG welding supplies and rods were like shopping the SEARS catalog as a child at Christmas time... We even could check out compressed bottles of oxygen n acetylene at no cost but had to bring back the mt bottles after using them up.
Gary Parsons
It's not cast iron so welded no problem, battery disconnected so no harm done with welding ,I weld cars on a daily basis ! It had a hole drilled and a screw in from a previous repair to keep it from slipping. I have made a splint and it won't happen again, it doesn't matter what it looks like as can't be seen. And I didn't really fancy changing it as it works perfectly well. It's 90 years old now so fatigue must play a part I reckon.
Pleased reading you sorted this out. Sorry for any bad information I sent you.
Gary Parsons


That's OK, I already had it welded by then, above pic of the Heath Robinson repair ( English term !). I had some trouble with it going accross to start with , realised I needed to adjust rod from vacuum cylinder to central position ,cleaned connections and shaft etc. while I was there. Been out on a road test and I would say it's shifting better than ever before ,a real joy . So I am leaving it exactly alone .
I think Heath would have been horrified. Just as well the sheet metal cover hides it.
At least she is shifting properly.
Well done.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.

