I don't know how handy you are but I make my own gaskets except the head gasket which can be bought from Olsons Gaskets. The wheel Cyl. and master cyl. will probably need to be sleaved. There are many places that do that. The pistons in the wheel cyl. are Alum and sometimes are so corroded they need to be replaced. Make sure who ever you send the wheel Cyl. to to sleave them has new pistons. I have had them say they did and when I got them back they used the old pistons. I don't know of any one making carb. kits. Not many gaskets in carb. Water pump is just a matter of replacing the shaft and the bronze bushing. I machine the gland nut for a oil seal instead of using packing. As Curt said Ken Clark can probably help you with all of this.
CORDially Mike
Mike thanks for the reply. I do most of my own machine work so a new WP shaft wont be a problem. What seal number do you use for the water pump gland nuts?
Ken is my next stop on my parts search.
Thanks Kory
The seals I use are National 470954 and the bushing can be gotten at McMaster Carr. Be sure and put some water pump grease behind each seal to lub. the lip and blue Loctite on the gland threads or water will leak by the threads since there is no packing used. Hope this helps.
CORDially Mike
Mike, Thanks a lot this will save a lot of time on the internet looking at seal specks.
Kory
A fix I learned from an expert Schebler old timer for the needle and seat is if it is leaking take the seat out of the carb., put it on a solid surface and "GENTLY" tap the needle into the seat. THATS GENTLY.
CORDially MIke
Thanks for the reply on the carburetor. I just pulled it last night and have it heading for clean up and rebuild this weekend. Overall it looks pretty good so I hope I don't find too much wrong inside.
After I pulled the carb and fule pump I started on the engine side covers. The valve covers came easy however the water cover bolts don't want to budge. I have a feeling I am going to have to add heat. Already had one bolt break off so I am not too keen on going after anymore bolts until I can get some heat or pretreating oil on them. I have the bad feeling they are through holes to the water jacket and they may be too long and corroded in place.
Anyway after looking inside I have decided to pull the engine and do a rebuild. The old mechanic in me just cant patch it up and make it run when I know looking inside it needs rebuilt. 90+ year old gaskets and oil caked up black as coal and gunk a half inch deep around the lifters is a bad sign.
Yes, water side cover screws go all the way through. It is common for them to brake off. Replace with SS. You will probably find the water distribution cover on the inside of the water side cover is rusted away. Figure on finding a new cover. Be sure and check cam bearings. If you are going that far put in bigger radiator core by extending out to match the tank in the front. Also, a high-speed ring and pinion gear since you are going that far. There is a real problem with getting pistons right know so be prepared for a long wait. When you are done you will be nicely rewarded with a fine running and beautifully designed car.
CORDially Mike
Once you get inside the engine check the bottom plate on the oil pump. It is made of die cast and can develop many cracks as old die cast tends to do. Have a steel one made to replace it if necessary.
CORDially Mike
Mike, Thanks for the info it helps a lot. I will post some pictures of my progress. Mostly I have been taking apart the roof and headliner to see what all is needed to fix the body. I am thinking that is going to be the one that will have the longest lead time to find items needed so I started there first. Now I am go on to the mechanical which I can do quickly as that is what I have done for several years as a job. Kory 
Thank you, I have already been in touch with him about body parts. It is going to be a fairly long list at the rate things are going.
Kory
The V windshield is quite interesting.
CORDially Mike
JMM,
Thanks for the encouraging words. I am on a path to do just that. The only wild card is the windshield right now. I will say every time I work on it I find another part that was cleverly repaired. Maybe not factory correct but it did work.
Kory
JMM,
Thanks for the encouraging words. I am on a path to do just that. The only wild card is the windshield right now. I will say every time I work on it I find another part that was cleverly repaired. Maybe not factory correct but it did work.
Kory
 
Cleverly repaired items is how I have found my 37 812 Cord. Someone gas welded another rear bumper bracket to the original bracket. I took pictures and posted them to the 812 forum and someone else pointed it out to me. Then the oil pan had a piece of 1/2 inch angle iron gas welded to the entire pan bolt rail. Only idea I can think of is someone was trying to solve an oil leak. Then the instrument dash lights never had the rheostat switch wired in. Even the bracket had the mounting eras cut off. I was able to buy another bracket but the rheostat switch was nearly impossible to find. One club member has an original NOS switch but wants $500.00 for it. I researched what Auburn purchased them for and in turn sold them for. They paid .16 cents and sold them to us for .95 cents in 1937. Randy Ema has the original Auburn catalogs telling what bin location and who they bought from and the cost. He has an amazing treasure of ACD information. Its amazing how early mechanics tried to "fix" a problem but usually made thing worse in the long run. Cord cars are all the same.. But they are all different. Towards the end of the factory run they had to put what they had on the cars during assembly.
 
 
Gary Parsons
Mike, You made a comment about getting the high speed ring and pinion gears. I just got mine apart today it looks like I have the 4.81 to 1 gears in mine. Also when I was removing the bolts I noticed the transmission cluster gear is getting pretty worn on the second gear back from the front of the case.
I did a little looking out on the forum and did not find any discussion on where to find these parts or who rebuilds them. Any info would be appreciated.
Thanks Kory
Your gear is the common one. You should get a 3:91 gear. You would be much happier with the car with a change. I might know of one available if you are interested. There were three transmission main shafts used so you would need to know what serial number your trans is to try and get the right parts. It can be found on the right ear of the case that extend over the frame.
CORDially Mike
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.


