Am following this because I too have to be purchasing and installing the exhaust of my non supercharged 37 Beverly.
Gary Parsons
Hi Gary and ddk2.
I'm not sure how much is common with the standad exhaust system and the supercharged system.
They maybe pretty much the same from the driver's floor area backwards. I do remember reading the supercharged system was slightly larger in diameter.
Many years ago I bought a standard exhaust system from Don Simmons which is show in the first and second pictures.
Then I had to make a new set of clamps and brackets using stainless steel to mount the system which involved quite a bit of work.
The attached drawings and sketches came from various sources.
The last picture shows the sort of tooling needed to make the clamps etc.












Thanks Terry for the great pictures. Way back in around 1965 I recall seeing the expansion chamber muffler on my car but it was very rusted out. Nothing was found from there back to the tail pipe. I do have some original clamps somewhere...
Gary Parsons
Thanks for the great pics and diagrams! The rear part is the same, the front is of course different and one of the most puzzling aspects on the S/C car. There are a variety of pipes and they are unlabelled but slightly different. Also puzzling are some short pipes with flanges on both ends.
These are the short pipes that have me particularly mystified.








These are photos of all the parts I have. I have lots of correct clamps so didn't show them.
It sure looks like you have way too many bits of piping.
Starting from the exhaust manifolds the bends with the small tubes welded at the side would connect with the manifolds and have the flexible chrome covering threaded over.
The plain bends would then be attached to bring the exhaust under the car to then connect with the Y shaped pipes.
I have no idea what the short straight pipes are for.
I would still try ringing Don.
Good luck.
Terry
ddk2, it looks like you are all set. I just don't see the hangers. The short pieces with the flanges on both ends are the connection pieces. you need to cut them to fit. Four pieces, cut to fit and welded onto the bends that have the SS covers on them. Make sure you have the SS covers and the two bolt flanges on the pipes before you weld on the pieces. The other two are cut to fit for the lower bends under the front fenders. I hope that all makes sense.
I'll look and see if I have a drawing for these.
Jim
Thanks all. Jim O'Brien I get the part about 4 of them being for the exhaust manifold connections but you've lost me on the other 2 underneath. Hopefully someone who has done a nice job with this has some photos or can take some. Clearly Don has a plan for each custom bent piece, I can't figure out why they aren't labeled and come with a diagram of what goes where. It's not like this is my first fabrication project.....
ddk2, these two drawings should help.
Mike


Thanks to Stan Gilliland bless his soul we can all see clearly how to set up a supercharged exhaust system.
Job done.
Thanks Terry this helps a lot. I didn't have the flanges for inside the fenders but since I'm not going for concours I'll probably try using stainless band clamps there if space allows. I'm also going to see if there are any properly set up cars in Florida I could go look at it no one has any photos of their installations.
ddk2, you have the straight sections of pipe with the ends formed to take the flanges.
I would recommend that you do it properly and don't take short cuts that will cause more problems in the future.
I'm in Australia and bought my exhaust system from Don Simmons as I knew I could fit it up myself rather that reinventing the wheel by having a system made locally from scratch.
ddk2Mar 20, 2026 Thanks Terry this helps a lot. I didn't have the flanges for inside the fenders but since I'm not going for concours I'll probably try using stainless band clamps there if space allows. I'm also going to see if there are any properly set up cars in Florida I could go look at it no one has any photos of their installations.
PM sent
ddk2, you only show 2 heavy duty flanges in your 1st photo. You need 12 to complete the job properly. You have the 12 nipples as show in the 1st photo.
1 - To do this job it is best to have the exhaust manifolds, fence, & fenders installed, with the fenders properly aligned.
2 - It is also best to have the main y-pipe and two smaller spider pipes that go under the fenders installed.
3 - Next install the exhaust screens and fender escutcheons so yo can check and make sure the pipes will go through the center as best possible.
4 - Each of the 4 pipes that will have the SS flex on them are different lengths, try placing the long straight portion of the pipe through the exhaust screen and down through the escutcheon to the spider pipes and you should find which on fits best at each location. They will probably be longer than needed at each end.
5 - At the exhaust manifold, for a clean appearance, you want nipple flush with the pipe. So cut 4 of the nipples with about 3/4" back and slide inside the 4 exhaust pipes. You may need to trim the exhaust pipe to get it centered to the escutcheon. Once you get all 4 fitted you can slide in the nipples and slightly clamp the flanges to allow movement.
6 - Now do the same with the connection to the spider pipes, centering to the exhaust screens. A couple of them may not tie in at the same angle and my need the nipple welded on at an angle as shows in Stan's drawing. Once you get everything centered with your nipples slid on and gaskets in place, tighten down the flanges.
7 - If everything fits good, take apart, and install the SS flex if you have not already done so, place the flanges on and weld the nipples in place. Reinstall.
Hope that helps - Mike
I think I would have ordered a supercharged Cord with the standard exhaust system.
Charles Cord had a Custom Beverly built with the Fast Back trunk lid and a supercharged engine with a standard exhaust system.
I had a short drive of this super rare Cord in Italy.
LV Mike thank you that step by step is extremely helpful. My plan was to reuse the exhaust manifold flanges as they are in good shape. I didn't understand the other flanged connections until this thread and the diagrams, so I will find more flanges. The exhaust system currently on the car was cobbled up back in the 60s and has no original pieces except the ones that have the stainless on them. Once under the fender they were just welded to the mess that was built. Course since the new system is stainless it'll have to be tig welded but I have a nearby restoration shop that's going to help me with that.
One other question, anyone have experience getting the stainless off the old pipes and onto the new ones? Tricks?
Probably determination and brute force. I guess you could check which way the spiral runs then twist back against it to try to get it to release from the inner pipes plus gently use a rubber mallet to break it free.
ddk2 - Bruce Earlin is in Florida(at least for another month) and has a S/C Cord. I don't remember how correct the exhaust is on it. Give him call, he's in the directory.
Thanks Jim will do.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
