Hi Thierry.
The two issues may be related. The clutch sticking on the is usually a linkage problem somewhere. Check the guide at the base of the firewall where the clutch pedal goes thru the floor. The other problem area is the shaft thru the frame.
 
For jumping out of second gear this was a known problem. The company added an interlock on the side of the transmission to prevent the transmission from jumping out of gear. The interlock plunger is connected to the clutch linkage. Disconnect the linkage at the plunger (pull the clevis pin) ansd slide the plunger out. Check the end to see if it is worn. The end is wedged shaped with a shelf behind the wedge. Many times the pins in the transmission wear grooves in the plunger and the pins no longer lock the transmission in gear. If there are grooves worn in either make a new one or weld up the old one and grind it back to the original shape. I'll see if I can find a photo of a warn plunger and post it.
 
When putting the plunger back in adjust the linkage so the plunger goes in as far as possible.
 
These two items will prevent the transmission from jumping out of gear unless there is a problem in the transmission.
 
Jim
I recall Stan sells these and all the needed coil springs. He's located in Wellington Kansas. Only available now two days a week thru email.
 
 
Gary Parsons
Hi Thierry,
Usually the end of the plunger is worn from the locking pins it engages. You can weld up the plunger and grind it back to the original deminsions. Also make sure the linkage is adjusted so the plunger goes all the way in and engages the locking pins.
Hi Theirry,
Yours looks fine. THere is some slight wear but that should be enough to allow the transmission to jump out of gear. I'm going to try and attache a drawing I did years ago that will give you the dimensions.
 
Make sure the plunger is going in properly. First look in the hole if you can, you should see two cones (one from the top and one from the bottom) with their tips cut off meeting just below the center of the hole. I hope that makes sense.
 
If you push the plunger in manually you can feel in it hitting those rods and then pushing them apart. You want to make sure the plunger goes in as far as possible. From the wear it looks like it has been engaging properly. hook up the linkage and have someone step on the clutch. You should see the plunger pull out, when the clutch is released the plunger should go all the way back in. If it is working properly give it another road test and see what happens.
 
If you have problems or hear strange noises get it back in the garage quick.
 
HI Theirry,
I'm sorry to say but it sounds like the problem is in the transmission. You said you changed the oil in the transmission - did you strain the oil as it came out? did you find anything in the oil such as spring parts, balls, etc? Try removing the main shift cylinder and the transmission cover and take a look inside.
 
In the mean time no more driving, you can go from bad to a whole lot worse very quickly.
 
You may have told us before but where are you located?
JIm
Moving forward on my problem, I am wondering if my problem is not related to the gear command.
 
When the problem occurs, on the second gear only, the gear does not disengage totally : I have an horrible gear noise, if I release the throttle, it comes back to normal. I decided to record the shifter and indeed, the gear command is moving. Here is a small video, look around 20 sec, you see the selector moving . On the video, the problem does not occurs (and I am wondering why as last day, it was the case)
 
 
My question is to know if that play in the command can cause a temporary disengagement of the gear and if yes, how to solve that
 
Many thanks
 
Thierry
What a good way to determine what
is going on.
CORDiallyMike
During the video I thought I saw the transmission moving upwards as if the frame was broken where the front spring rests.
 
 
Gary Parsons
As long as we're still in the troubleshooting phase, does the problem go away when the transmission cover is off? I have seen problems with the shift linkage hitting the transmission cover, not allowing full travel or engagement in gear. Just something else to consider. Check the bottom of the cover for wear marks/clearance.
 
Cheers, and good luck.
Hi Thierry, I have watched the video several more times. I don't see any movement of the transmission as Gary thought. Also the problem t.Hills discribed is on 3rd gear, not second. The more I have thought about this problem I think your issue is in the gearbox. I would suggest you pull the main shift cylinder and take the cover off the box and look inside. Please post a couple of photos, especially looking straight down at the 2/3 syncronizer.
JIm
Hello,
 
thanks all for your replies.
 
Here is a new video : Video
 
I still don't know if the 2nd gear goes out because the plunger moves a bit, or is it due to the actuator ?
 
Any idea ?
 
Thanks
 
Thierry
The sound made in the gear issue worries me. Please do as suggested by Jim and remove the transmission cover. Get some pictures on the gear arrangement for posting here. I suspect something wrong with the synchro clutch because it seems to make a grinding sound as the lever moves forwards disengaging the gear.
 
 
Gary Parsons
Hi Thierry,
 
In watching the video I think it is jumping out of gear which results in the cross shift lever moving some. When you depress the clutch it pulls it back into 2nd gear. I wonder if the transmission is getting all the way into second gear? I can't tell from the angle of the camera.
 
Either way there are some noises there that don't sound good. Please pull the main shift cylinder and pull the cover off the transmission and see what is going on in there.
 
Jim
You could try contacting Perrin Youenn in Bretagne, France.
He has just about completed the restoration of a Custom Beverly Cord.
You guys could probably talk more easily to each other.
Just a suggestion.
atp035@hotmail.fr
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.

