Stan Gilliand in WEllington Kansas will have the seals you need. Theyare NOT original but a better modern seal now. I do have two NOS seals for the large diameter hub. They are a metal leather flat spring type seal from that time period. I will look for them and post pics for everyone not familar with what original looked like.
I can't help with getting the balls back in because I could never get mine out. I tried as instructed but nope...Wouldn't happen. I too am not "that smart"...
 
 
Gary Parsons
hi Robert,The first question is do you have the Bendix joints or the Rzeppa joints? The most common is the Bendix. What wears out on the joints is the races. THE balls are a lot harder. Carefully inspect the races and see if they are smooth from one end to the other. If the joint is together see it it is loose or slop in the joint when you twist the shafts. If the joints are worn out you can grind them and put in oversized balls. The seals for the bell and the outer bearing are standard seals and available at any bearing supply house. The bearing originally was a special bearing with tight internal clearances. These are no longer available but you can get the same bearing with standard clearances, these work fine as long as the rest of your front end is good. Again these are available at your local bearing supply house.The next question is which housing do you have, the bolt in or screw in type. This determines which seal you need in there.For the balls - if you have the Rzeppa the attached drawing tells you how to do it. If you have the Bendix you start off with the center ball and then put in three of the outer balls. to get the fourth ball in cock the joint all the way to one side and place the ball in the slot where it goes. Take a large wooden dowel and a hammer and tap it in place. You need at least two people to get this done. Also do it in a clean area since the balls tend to pop out and hide in far corners of the work shop.Have fun! it can be a pain to try and get this done. One of the joys of working on a Cord!JIm 
Another method of assembling is a little more complex. There is a drift pin located in the short knuckle which prevents the locating pin for the center ball from travelling to far. Remove the drift pin and push the locating pin all the way in. Now turn the center ball with the slot toward the last empty pocket (four of the 5 balls should be in place) and slide the 5th ball in place. Once all 5 balls are in there pockets , rotate the the center ball and let the locating pin fall in place . Then insert the drift pin .
Seems a little complex but works without forcing. Also anyone wonder what the slot in the center ball is for?
Its to allow just enough clearance for the 5th ball to fall in place
Dear Mr. Houser,
Responsive to your post #41723 above I DO NOT think you should "assume " the Bendix outer universal joints are "interchangeable". Please refer to my post #41695 above dated 12-5-20. Based on the "CORD ENGINEERING CHANGES 810 & 812" notes there were at least three distinct angle grinds , viz. 35 degree , 37 degree and 18 degree. There is commentary at Page 27 of the ECNs that Bendix' Mr. Sturgis was asked by Auburn Automobile Co's L. R. Jones to mark the 37 degree joints by some more permanent means than "the daub of yellow paint". Whether Bendix complied is not known to this writer but I have noted several outer U-joints/shafts marked with the daub of yellow paint. I am not a skilled mechanic nor trained in machine tool technology and engineering. I don't know how and where to measure the angle grind of the race. That is why I have solicited the input of those who are qualified to advise us on these issues. Certainly I do not wish to make a mountain out of a mole hill but I would proceed with caution and get good and competent guidance when overhauling the front drive components. It seems to me that proper drive train assembly and adjustment is tantamount to good driveability and dependability of any Cord Model 810 or 812. Let's hope we receive some additional input to this thread, Jack Richards.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.

