I have the same situation with S/C Custom Beverly. I think mine is because shift fork ends don't line up correctly. I just shift into 3rd before stopping and making final shift into 1st. It's possible a shift fork is worn or maybe the set screw isn't seated in the proper spot. You can remove the front shift housing assembly and check.
Pat Leahy
HI Bill,
You might want to check the cross shift. There may be some slop in the cross shift so when you shift from 2nd to neutral the shift doesn't get into neutral so when it tries to move to the left to go to first it gets hung up and can't move over. The same thing would happen if the clevis on the main shift cylinder isn't adjusted properly. 
 
The main thing is to pull the sheet metal cover off and see what happens when you try to shift and it doesn't go. This give you the clue as to where to start troubleshooting.
 
Also a note - the shift rails are inside the transmission. First and third use different shift rails.
 
JIm
Hi Jim,
Thank you very much for the response, I will remove the bumper and cover and check how everything is functioning. ┬áWhen I first got the car from Gail Shaw I donÔÇÖt remember this issue occurring so it seems likely that something has gotten out of adjustment.
 
Also, thank you for correcting my nomenclature, 1st and 3rd are on the same solenoid but not on the same shift rail.
 
Hopefully I will be able to correct this before I take the car to the West Coast Meet in October.
 
Best regards,
Bill
Hi Jim,
Thank you very much for the response, I will remove the bumper and cover and check how everything is functioning. ┬áWhen I first got the car from Gail Shaw I donÔÇÖt remember this issue occurring so it seems likely that something has gotten out of adjustment.
 
Also, thank you for correcting my nomenclature, 1st and 3rd are on the same solenoid but not on the same shift rail.
 
Hopefully I will be able to correct this before I take the car to the West Coast Meet in October.
 
Best regards,
Bill
Riley,
I recently had a similar problem with my Cord. After it warmed up it would not shift into 1 st gear reliably. My problem was that the main shift cylinder clevis was not quite in the center. I readjusted it and the problem went away! Hope this helps.
 
Dan
Back in 2011 when my Cord went on the road in Australia I had problems getting 2nd and 3rd gear when it warmed up. I removed the sheet metal cover and could not find anything out of order. Driving the car from cold with the sheet metal cover off she changed gears perfectly all the time.
Eventually I discovered wear in the cross shaft keyways. Nothing got out of synchronization unless it warmed up with the sheet metal cover in place.
The main vacuum cylinder had caused the problem with its brute force.
At the time my Cord had travelled around 300,000 miles from new.
The main vacuum cylinder has been fitted with flow restrictors.
Thanks to everyone for their responses.
 
Dan, your suggestion was very helpful for me as it pointed me towards a mechanical linkage issue instead of an electrical problem. ┬áToday I removed the bumper and transmission cover on my Westchester and assessed the linkage adjustment. ┬áIt appeared that the transmission shift lever was not tight on the shaft and had some play that might have been effecting the reliability of the shifting. ┬áI tightened the clamping bolt for the lever and then readjusted the power cylinder clevis for neutral. ┬áAfter a brief diversion to address a Startix issue where the starter circuit welded closed causing the starter to run continuously (donÔÇÖt you love it when extraneous problems arise when you are correcting an unrelated problem) I was able to take a test drive and the car now seems to shift reliably after warm up. ┬áI have not replaced the transmission cover yet but hopefully the reduced cooling of the transmission will not significantly effect the shifting performance.
 
Thanks again to everyone for their help.  I look forward to reliable shifting in Cambria at the West Coast meet (knock on wood).
Bill
Looking forwards to seeing this car in October. I finalized my reservations yesterday for this event.
 
 
Gary Parsons
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
