Hi Blackiron, Yes there is a problem somewhere. with the clutch depressed and the shift selector in neutral the cross shift should be in the middle.
 
Hard left looking from the front is 4th gear. So the first question is does this only happen when you are coming out of 4th gear or does it happen all the time? If it only happens when you are coming out of 4th gear I would suspect it is not coming all the way out of 4th gear.
 
From your post it sounds like this may have just started and is happening all the time. Try the following trouble shooting
1. Shut the car off and see if the cross shift pops back to the center neutral position.
2. Start the car, place the shift selector switch in neutral - does the cross shift go hard left
3. Check voltage on the rear most terminal on the solenoid valves - it should be 0 volts
4. Disconnect the vacuum line on the left side of the cross shift - this is a bit difficult as the line is on the bottom below the cross shift switch. Is there vacuum there?
 
Stop as soon as you get a yes to any of these questions - you have found the problem
Give me a call if you have any questions, I am in the directory or I will PM you with my number.
Good luck! and let us know how you make out.
Jim
Your issue sounds like vacuum is always on the cross shift shaft holding it over to the 4th gear gate. If this is NOT an electrical issue I suspect your shift solenoid valve is leaking vacuum so the shaft stays hard over to the left. As Jim suggested. Start working thru this till you "find" the issue. Something is telling the cross shaft to stay hard over. With the engine shut down the shaft will return to the true neutral position.
 
 
Gary Parsons
I found this on You Tube. It clearly shows where neutral is supposed to be.
 
 
Gary Parsons
Thanks for the quick replies guys. I donÔÇÖt know how long itÔÇÖs been like this, maybe thirty years, maybe yesterday.
IÔÇÖll follow your suggestions and report back.
Thank you
Well, found the problem. The circlip holding the rotary selector switch in the steering column arm had come out of its groove allowing the switch to move slightly out of position.
An easy fix, thanks all.
Really happy you found and fixed the problem. So it was an electrical issue sending a message to the side shift shaft to stay hard over to the 4th gear but not actually in 4th gear.... Good deal...
 
 
Gary Parsons
Graham,I am amazed that you found the problem so quickly ............ well done!
Installing or removing the rotary switch is not such a problem if you have the right tools.
I will get some pictures of the tools I made tomorrow and share them.
Terry. I too am interested in seeing these tools because I will have to do this job later on.
 
 
Gary Parsons
Attached are the simple tools I have used to remove as well as install the circlip that holds the gear selector switch.1. The circlip has to be pushed through a tapered section inside of the switch housing. The tubular plastic tool does this job.The tubular plastic tool was machined a PVC water pipe fitting ( from memory)The large end is 38.5 mm diameter with 2 mm wall thicknessThe small end is 33 mm diameter with 2 mm wall thickness.The slot which is about 19 mm wide allows the tube to compress.Overall length is 130 mm2. The small threaded rod is used to compress the internal spring inside the switch. I didn't have a piece of 3/16" threaded rod, so I just used what was convenient. The wooden spacer keep the nut out in the open.Overall length is 190 mm3. A couple of long thin tools are handy to remove the circlip. One has a wedge shaped end like a screw driver and the other has a small hook.Both are about 190 mm longIt helps to keep these tools in a small box marked with "Switch Tools"They are fairly easy to make and do work. 
Terry
Your tool and description would make a nice article for the newsletter.
Russ
Terry
Your tool and description would make a nice article for the newsletter.
Russ
 
I agree. This is a great idea.
 
 
Gary Parsons
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.

