Bill the material is no longer made. There is a solution. I had a sample of the correct material to work from that was supplied by Tom Georgeson. I found a base material with the same weave pattern then experimented painting it to get the correct colour. Then the job of drawing black lines at 45 degrees and uniformly spaced on each panel began. I used a marker pen for this in-conjunction with a mechanical drafting board. Eventually the panels were glued to thin carpet to stiffen them up before the panels were cut to match cardboard templates. It took quite a few weeks to complete the job.I found that early production Cords had a wider spacing pattern for the lines compared to later production cars.Thank God mine was an early production car which made drawing the lines more manageable.The carpets were made by others to templates I made.I can send you some material samples to get started if you like.
Terry,
Rick Hulett has been the recognized interior expert for many years. The sample you show looks like one I got from him earlier this year. Did you also get carpet and striped material patterns from him?
I recently installed one of his trunk kits in my phaeton. The stripped material is a burlap adhered to a jute backing about 1/4 - 3/8 inch thick. This material was only attached to the side walls, back of the rear seat, and inside of the trunk lid which was also trimmed with the interior leather. A beige carpet covers the trunk floor on the left side of the spare and a separate piece also is on top of the shelf over the spare tire and draped over the rear of the spare down to 2 snaps just inside the trunk lid. There is no stripped material attached to the trunk floor.
I believe Rick indicated that all the trunk carpet material, except for the the cabs, was the beige material.
He did not mention differences in stripe width with manufacture date in my emails and phone conversations with him.
Hi John, yes I had been in contact with Rick Hulett unfortunately he missed out on seeing the finished job. He was the inspiration to do a good job.There were some remnants of the original striped lining in the compartment under the front seat, behind the back seat and in the trunk lid. Both have the wider spacing. I have not taken a picture of the panel behind the rear seat but it does have the sam pattern.Rather than have a long narrow strip of the striped material just under the jack shaft I made it wider and slid one side under the bottom metal cover of the trunk opening. I think the sample I have originated from Rick but it was sent to me by Tom Georgeson a long time ago. My Cord is an early production unit with Serial No 810 1586 A which probably accounts for the different pattern. My car had never been restored so I don't think the striped material had been changed.
Terry'
You are very lucky to have a car that hasn't been messed with. There are very few out there with as much original material as you have. Most people would have had to go to Rick to get as much info as was still in your car.
At the Auburn reunion this year I talked with one of our directors about what the club might be doing to start gathering up any information such as Rick had in his many original pics of details of the interior and trunk trim that is invaluable when trying to restore a Cord. The reply was to the effect that I should compose an article to send to the editor of the Newsletter on this subject to garner support for club moving in this direction.
This was a disappointing answer for me. It seems like a no-brainer that this info needs to be preserved for the good of the club and the members, to more easily allow the members to restore and preserve their cars, I believe the Directors and elected officers need to take the initiative now before Ricks and others files are lost.
Hi John McCall and Jack Richards.
Yes, I have been very fortunate with the amount of original material my Cord contained plus the help of many fine members of our club some of whom are no longer with us to restore my Cord. Rick Hulett shared with me a wealth of information on original Cords that he photographed over many years. I have everything he sent me stored in emails. It is there for others to use too. I suppose we do need somebody to collate it all. I am open to suggestions.
Maybe we need a Rick Hulett interior photography page on the website ?
 
I also think we should add an original factory photography and new car photography page divided into A, C , & D and grouped by key model years (ex Auburn 1934 - 1936) - I would be pleased to moderate such.
John.This looks like the original trunk lining material that has faded with time and new carpets. This trunk lining has a fine line spacing. I saw another Cord in the park in 2018 with the same material. I took some pictures of the lining but can't find them. I will keep looking.Found them! Rick Hulett told me this greyish material had faded a lot and was originally the colour shown in the attached small sample in the last picture.In the park I just happened to be photographed while taking my pictures.
I have numerous emails from Rick this year, that contain pics of original phaeton trunk details, that I discussed very briefly with Jim O Brien at the reunion. He also indicated a willingness to try to correlate/summarize the info if I sent it to him. If we could get enough people to send in info that they have gathered from various sources it would be a step in the right direction. I believe getting it on the web is also the right direction.
Rick , trying to make a buck specializing in interiors, was at the same time extremely free with his knowledge and time, to individuals trying to restore their cars. Hats off to that attitude.
I can see that gathering restoration info is generally popular with those that read and replied to this forum. Is there also a more widely read forum that would reach more eyes?
My beverly has its original interior.If any pictures or information is requested in any detail I will share what I have. I do not have the front kick panels under the dash or any trunk lining. My headliner is complete down to the moth holes and the wire stays too. In 58 years of family ownership I have NEVER rolled it out to look it over completely.
 
 
Gary Parsons
I didn't get chance to look at Marks trunk as I was soo'd away by one of the judges although I talked to him quite a bit and was very impressed with his knowledge of details. He did say that Rick Hulett went with him when he went to look at the Westchester.
I am surprised however that the lines show on the back side of the rear seat as Rick told me, and his installation instructions say, that the lines should face forward on that piece of material with the raw jute showing in the trunk. Since he didn't have a source for the raw jute he said just turn the piece so the lines face forward.
John there is a striped trunk lining panel behind the rear seat which is inside the car and then there is another striped panel in the trunk .
Check the attached layout diagram.
On another note I made a drawing of the wires that pass through the head lining which is full size and can be used to make new stays in stainless steel. 
Terry,
I stand corrected. There are 2 jute panels, one on the back side of the rear seat with lines facing forward, and another at the front of the trunk with lines facing rearward. I will have to make sure I refresh my memory by looking at what I did before commenting the next time.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.






















