Jim is correct. The exhaust was wrapped on Asbestos and had a canvas cover applied over that. The hasteners were simalar to the design of the under hood wire fasteners along the radiator supports that held the horns.Stan sells them.
 
 
Gary Parsons
Bill,Here are a couple of photos. The exhaust insulation clamp, some original insulation and clamps and the type of hose clamps for the water tubes. The asbestos insulation was pre-molded and came in two halves that slipped on the internal exhaust pipes and were held on with three clamps. I have never seen a canvas covering on the original asbestos.Jim
[
Jim I have pictures of the Cord I saw at last years West Coast Meet in Morro Bay. It was an unmolested original car. Mark Tomei was looking under it. I was asking Randy Ema about an additional copper tube extension to the oil cap area for the throwout bearing. Ron Irwin as asked by Randy was that extension original. No was his answer. I did not ask bout the Asbestos wrap of canvas but did notice it was original and the clamps were original too. I will transfer the pics from my phone to my computer to post here but... I need my daughters help.I'm not bright on picture transfers or much about computers.
 
 
Gary Parsons
Hi! Recently had a manifold repaired. Nox Vidmate VLC When it was re-installed the guys used a worm drive clamp to cinch-up the asbestos sock on the exhaust line immediately after the manifold. That can't be correct' date=' but what is. Is there a list I've missed for the proper clamps for the rest of what is under the hood? I thought I'd spend rainy summer days sprucing up the engine bay. Correcting the clamps seems to be a worthy project.[/quote']The hasteners were simalar to the design of the under hood wire fasteners along the radiator supports that held the horns.Stan sells them.
Hi! Recently had a manifold repaired. When it was re-installed the guys used a worm drive clamp to cinch-up the asbestos sock on the exhaust line immediately after the manifold. That can't be correct' date=' but what is. Is there a list I've missed for the proper clamps for the rest of what is under the hood? I thought I'd spend rainy summer days sprucing up the engine bay. Correcting the clamps seems to be a worthy project.[/quote'] The hasteners were simalar to the design of the Speed Test Scrabble Word Finder Solitaire under hood wire fasteners along the radiator supports that held the horns.Stan sells them.
I was at that West Coast meet. I too saw this unmolested Cord. I was standing with Randy and Ron and asked Randy the same question about the oilier for the throw-out bearing.Ron said it was NOT original. Also the rear bumper has an extra stiffener piece added for the tow hitch. It too was not original. The asbestos pipe insulation on the exhaust header pipes was original and it was held to the steel pipe with band clamps. The same pipe insulation can be made today using a material called calsil. It comes in different thickness and pipe size up to about 30 inch diameter. Its common in power generating steam plants. I used it plenty in the distant past.
 
 
Gary Parsons
Years ago Melvin Clemens was told a worm drive hose clamp was not correct of
J357 and his answer was "It doen;t leak anymore"
Bob Roller
Right on Bob. Do you want to drive or look pretty.
CORDially Mike
Mike you can have both. Some of the period style clamps I bought would not close up enough to suit the hoses on the engine. I simply made my own period looking hose clamps. To bridge the gap I fitted a small stainless steel strip with both ends tapered on the hose and tightened the screw. They look good and don't leak.
I was at the West Coast meet too, and I also saw the unmolested Cord. I was standing with Randy and Ron, and I asked Randy about the oilier for the throw-out bearing. Ron said that it was not original. The rear bumper also had an extra stiffener piece added for the tow hitch, which was also not original. The asbestos pipe insulation on the exhaust header pipes was original, and it was held to the steel pipe with band clamps. Today, the same pipe insulation can be made using a material called calsil. Calsil comes in different thicknesses and pipe sizes up to about 30 inches in diameter. It is commonly used in power generating steam plants, and I used it extensively in the past.
 
https://sites.google.com/app-xyz.com/spectrum-tv-app-for-pc/
Band clamps: These are the most common type of exhaust clamp. They are made of metal and have a smooth, rounded edge.
 
https://motherprideacademy.com/sainik-school-coaching-in-up/
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.









