Hi,
 
I suspect that the bearing in the steering wishbone has failed. It is New Departure 900916, and it is rare. Right now there is one on ebay because someone found a few NOS ones at a garage. If you might need it, or want it as a spare, you might consider buying it now. You can always re-sell it.
 
http://www.ebay.com/itm/NOS-Steering-Cr ... 2d&vxp=mtr
 
--Tom
 
EDIT: The other two likely points of failure are the steering box--rebuildable but not cheap--and one of your front U-joints--Not cheap at all. Let's hope for the best!
 
--Tom
Thanks Tom. Assume the bearing is in the top part of the wishbone that's bolted to the shaft that comes out of the steering box ? Is their any way to tell if the bearing has failed without taking the wishbone off ? Is there any trick to removing the wishbone - looks like just the big nut at the top and the cotter pin and plug in the shaft on the bottom ? Is the bearing a pressed fit ?
 
Bill McL
Hi Bill,
 
I am referring to the Big W "Intermediate Steering Arm" that is positioned under the front motor mount and to which the Pitman arm from the steering box and both tie rods are connected.
 
I think to diagnose this entire problem I would engage the services of an assistant to turn the wheel through its free play while I watch to see where the motion is being lost. There should be NO slop in the intermediate steering arm bearing. If the arm is moving sideways, up and down, or back/forth, the bearing is damaged.
 
In any event, I would--and did last week--purchase a rare 900916 bearing and put it in my "Cord Unobtainable Spare Parts Box" along with several other items.
 
I noticed that the EBay vendor's supply of the bearing went from 2 to 0 since noon. Did you buy one that he sold? Just curious.
 
--Tom
Tom:
 
Thanks. I had one but did purchase one from the eBay vendor.
 
Bill
Bill,
If you heard a "pop" it sounds like you broke something. I would tend to doubt the 916 bearing itself failed and gave you that much play. It's possible the bolt or one of the U-bolt mounts for the plate failed.
 
Also take a good look at your steering column (between the steering box and the steering wheel. I have seen several cracked or broken at the steering box because someone didn't mount the box and shim the steering column under the dash correctly putting a bend in the column and the column eventually fatigued.
 
To answer your original question, yes you can adjust the play in the steering box. You need to center the steering box and adjust it so there is no play. When you turn the wheel to either end there will be some play do to the geometry in the box.
 
Let us know what you find.
 
CORDially,
Jim
Tom & Jim:
 
Thanks for the advice. I had someone move the steering wheel for me. There seemed to be no play in the wishbone bearing once the wheels started to move. However, the cross shaft lever connected to the steering box didn't move during the approx. 1/4 turn of the steering wheel before it started to move / engage the wheels.
 
So, I think I can assume that the bearing in the wishbone is likely OK and it's either something in the alignment of the steering col. or something in the steering box, or a broken bolt.
 
I'm not quite sure what you're referring to in the "It's possible the bolt or one of the U-bolt mounts for the plate failed." Is this referring to how the steering box is held down ?
 
Bill
What ever the problem is DON'T drive it that way!!!
Cordially Mike
What ever the problem is DON'T drive it that way!!!
Cordially Mike
Had the same problem recently, balls had broken in steering box sector shaft (drop arm). Easy enough to replace but steering box must be removed and dismantled, hopefully bearing outer ring and sector shaft bearing tracks are undamaged ( mine were OK). New balls can be purchased from Bal-Tec CA, they are .209" diameter. Mike is right, do NOT drive, or in fact turn the wheel until repaired to avoid further damage
to bearing surfaces.
Graham
Hi,
 
Good advice. Good diagnosis.
 
--Tom
New balls can be purchased from Bal-Tec CA, they are .209" diameter.
 
Graham - Thanks. Do you have a part number as their balls run 5 decimal places and I think they have 3 at the .209
 
Bill
New balls can be purchased from Bal-Tec CA' date=' they are .209" diameter.[/quote'] 
Graham - Thanks. Do you have a part number as their balls run 5 decimal places and I think they have 3 at the .209 
Bill
Hi Bill, difficult to measure past four decimal places, but balls I used were .209219", a few tenths either side will make no difference. To confirm this is the problem, simply rock the steering wheel while someone watches under hood, if steering shaft is moving and drag link is not ..... Bingo !
Graham
Graham:
 
Thanks. I put a work light down in that area and moved the steering wheel by hand and the arm that comes off the steering box (Pitman arm / Drag link ?) did NOT move during the approx. 1/4 turn of the steering wheel - confirming that the problem is in the steering box.
 
Am preparing (with advice from others) for the removal of the steering box and column for repairs.
 
Bill
Quick Update:
 
With the help of Mike Brady, I took the steering box out (of course, having to undo a whole bunch of other parts) and found at least 1 ball on one side and I'd say close to 1/2 the balls on the other side missing in the cross shaft roller assembly. It's currently at a machine shop for rebuilding.
 
Bill McLaughlin
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
