Thanks, Mitya!
 
Welcome to the ACD Forum- We enjoy seeing your pictures and progress! We would also invite you to join the ACD Club, and tell us about your experiences in Belarus.. www.acdclub.org ..
 
Steve
Today my goal is to prepare the car for a 2000 mile trip. It should take place at the end of June 2025. I have to prepare the car for the trip as much as possible. I repaired the gearbox, replaced the secondary shaft bearing. Made a new wiring harness from the gear shifter to the gearbox.Made an exhaust system.  
Hello Mitya my name is Terry Cockerell, I live in Australia. I have a friend and fellow ACD Club member Pavel Mates in the Czech Republic who is restoring a Westchester.
His email address is messermat@seznam.cz
I'm sure he would be delighted to hear from you.
Hello Terry Cockerell. Yes, of course, I will contact Pavel Mates. Thank you!
 
Mitya
Thanks Terry Cockerell!
We want to do a full restoration of our Cord, but this year I am restoring a 1939 LaSalle. After that, I will do the Cord. My friend has been looking for an affordable Cord for years. This was not a spontaneous purchase. This car has been his dream for a long time.
 
Today I'm assembling brakes.
 
Continue to repair the car.
The brake system has been updated. I replaced the brake pipes, cuffs in the brake cylinders and in the main brake cylinder. Today I filled the brake system with DOT4.
I removed the gas tank and washed it from dirt. I repaired the fuel sensor. The old brass float was all cracked and there was gasoline inside. I replaced it with a plastic one.
 
Somebody in the US was making exact copies of the original air filter/silencer. Don't know the guy's name.
One of the copper pipe vacuum lines from the transmission connects with the air filter/silencer.
Hello, Terry Cockerell! Yes, I know about connecting tubes. Today the rain did not let me finish.
 
 
Mitya
The copper line Terry is talking about is very important. It draws a slight vacuum on the crankcase thru them oil fill tube. This small amount of vacuum keeps most of the oil from leaking out the front and back main seals. Actually the Cord engine doesn't have any normal form of a crankshaft seal. Just the vacuum and a drip tray area.  So please make sure you have this in place.
 
 
Gary Parsons
Your correct Terry. I had forgotten about that line from the solenoid pack. Its just a vent as I recall. There also is the vacuum port on top of the intake manifold that allows vacuum to run the cross shift and the main vacuum can that pushes or pulls the shift lever into or out of gears. Tomorrow I plan on looking into my crankcase vacuum line to see if it has the rolled up copper baffle or not. I do understand how it works off the venturi effect from the carburetor pulling in air. It can be a simple but also complex system. Thanks for posting the information. It can help everyone. We have a member from the state of Montana that kept finding oil leaking near the clutch. He removed the engine a "few times" trying to find the leak. I was suggesting thru a mutual friend how to find the leak... Turns out the rear main cap had a hairline crack in it. It was impossible to see but it was finally found and replaced.
 
 
Gary Parsons
Hello, Gary Parsons. I have prepared two separate tubes. One tube for the intake of crankcase gases. The other tube for the supply of clean air to the gearbox mechanism. The two tubes are located in different places, since the air flow through the filter has different strengths. One tube needs a strong flow, the tube to the gearbox needs a weak flow.Mitya
 
Member Tom Dudley in Michigan made many of these air filters. Contact him @ mkilleen@charter.net
First quality workmanship.
Hello, Gary Parsons. I have prepared two separate tubes. One tube for the intake of crankcase gases. The other tube for the supply of clean air to the gearbox mechanism. The two tubes are located in different places, since the air flow through the filter has different strengths. One tube needs a strong flow, the tube to the gearbox needs a weak flow. 
  In this picture the tube to the right is the atmosphere vent from the 4 solenoid shifting block on the passenger side of the car. The copper line that connects to the intake manifold is the high vacuum that connects to the vacuum side of the 4 solenoid block on the passenger side of the car or transmission. Finally the copper line that is connected to the top of the oil fill spout needs to be pointing up so the venturi of air being drawn into the carburetor can pull a small amount of vacuum on the engine crankcase. All this may seem complicated but once you see it things make sense. 
 
Gary Parsons
Mitya 
[attachment=8222]IMG_1253.jpeg[/attachment][attachment=8223]IMG_1239.jpeg[/attachment] 
 
 
In the first picture showing the underside of my original air cleaner/silencer you can clearly see the two holes with the larger one connecting with the tube from the oil filler pipe.I do not understand your need for different vacuum strengths.The second picture show what had to be done to install a replaceable air filter.Note. The screws connect with a flange that has tapped holes and two lugs passing through the opening.
Hello, Terry Cockerell! 
The tube that comes from the oil filler neck must have a vacuum. This solution is clear. The solenoids block has an input and an output. On one side is the vacuum from the engine, on the other is the air input from the atmosphere. This input must be cleaned so that dust does not get into the solenoids block and into the entire system. As I understand it, if you bring the tube close to the carburetor, then a vacuum will also be created in it, as in the tube that comes from the oil filler neck. Therefore, I decided to bring it to a wider area, where the turbulence of the air flow is less and a vacuum is not created.
 
Mitya
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.














