The question centred around installing a supercharged spec camshaft without the addition of a supercharger.
So why would the heavier chain drive be required ??
The question centred around installing a supercharged spec camshaft without the addition of a supercharger.
So why would the heavier chain drive be required ??
 
Terry your exactly correct. I just was asking in installing the CAM would change performance any. Cliff is correct about changing all the other parts IF you were to actually run a supercharger. I never planned for that in my original question. Just was "dreaming" about swapping in a supercharged cam for a non supercharged cam... Nothing more...
 
 
Gary Parsons
Example: I am running a supercharged Auburn engine in non-supercharged form - the prior owner wanted the balanced crankshaft that is only found in the S/C. As to the supercharged cam - I assume that is in there too, but I believe they are same and on non-S/C I believe you have the same firing order as S/C with just the addition of dual points (and know for sure it is running on a standard distributor).
 
As to a Cord running the cam only - I thought the supercharged distributor has a different firing order, so does the S/C cam change have different valve timing and as a result you must run a S/C distributor too or apply the S/C firing order to a non - S/C distributor ?
The standard ( unsupercharged ) runs an 8 lobe cam with a single set of points.The supercharged engine runs a 4 lobe cam and dual points with a different firing order.Reason for dual points is to increase dwell, the number of degrees the points are closed to build up coil power. One set makes and the second set breaks the circuit . A supercharged cam will run in a standard engine with an 8 lobe distributor. Just change the firing order in the dist. cap.
I have one in my 810.
Thank you George for this detailed explanation. Are you expecting any improvement in power or economy?
 
 
Gary Parsons
A couple of corrections - on the dual point distributor each set of points controls the spark on 4 cylinders. That is why the points have to be synchronized - so all the cylinders fire at the same point in the cycle. Either distributor will work with either cam.
 
I was once told that changing the firing order from the standard to the S/C firing order will increase the horsepower by 25 HP. I was also told, by someone else, they put a S/C cam in a standard Cord and was disappointed by the results. I have never seen data supporting either one.
 
However it gets a lot more complicated then just changing the cam. The two cams are very different. First is the firing order, Second is the lift profile, third is the valve timing, fourth is the valve overlap. The firing order is fairly obvious. The other items have to do with the stand engine is sucking the mixture into the cylinder while in the S/C engine the mixture is being blown into the cylinders. Therefore the engine breaths very differently and this must be taken into account in the design of the cam.
 
So the bottom line is yeas you can put a S/C in a standard engine and just move the wires around for the firing order. However you may not get the performance you want.
Thank you Jim for this great explanation. I really was not looking for hp improvement but was just looking for the possibility of changing cams and what may happen. You mentioned the 25 hp gain but also said someone was not happy after changing cams. I recognize our drive train can easily handle the added 25 hp because it can handle the supercharged engines easily.
 
 
Gary Parsons
Thanks for the clarification Jim. I once drove Harold Allsop's 812 Cabriolet . It had a supercharged cam in the standard engine. It had good performance .
It likely had the 47-10 gear ratio which also helps.
I know this is a 5yr old zombie thread. What I didn't see addressed was an increase in compression to be able to enjoy the engineering designed into the engine for the boost from the supercharger. I'm told it's modest, maybe 5lbs at full zoot. I'd think that in order to reap the benefits of everything intended, minus the whine of the blower, every system should be detailed. Exhaust should be ported, make the manifolds bigger at the opening than the block ports. Make the intake ports in the block a little bigger than the manifold. This would create reversion dams to keep a more homogeneous fuel/air mixture. Tuning would need to be precise, almost an unhealthy level of attention to timing, dwell, carb jetting. True dual exhaust, custom valve angles that begin with a straight 90Ôü░ cut above (below, flathead) the 1st angle. On the intake side, create a venturi effect by expanding the port volume ahead of the 90. Could it be done? Why not? Is a guess of a realistic increase of 25% improvement in performance realistic? When not opened up in anger I'd also suspect incredible low speed and drivability manners. If I had the means I'd be all over it. Perhaps some of this could also be achieved without the supercharged cam, just tune, porting, compression, and maybe the crank (I'd seen above that it was better balanced). Kool topic...ƒÿÄ

I think the blower is doing nothing until you get over 2500 rpm? I have never driven an normally aspirated 812 but I can tell you that our cabriolet which has a 100% factory supercharged engine in it really moves.
I had a ride is a 1935 Supercharged Auburn phaeton here in Australia that had brutal acceleration. My pal the owner just stomped on the accelerator in any gear and we were thrown back into the seats.
It was astonishing to experience. I remember reading Bill Baster the engineer who laid out the overall design of the Cord engine had a supercharged Cord. He was challenged to a standiing start race but I can't remember what the other car was . Bill won easily. That was back then when parts were readily available.
Today is completely different with replacement gears virtually unobtainable. I have a very nicely restored 810 Westchester that will comfortably do 60 mph all day and easily hits 75. I have never pushed it harder. What is the point? It is almost 90 years old and I feel deserves to be treated with respect.
The weakest link in the drive chain is the gearbox. The teeth on 2nd, 3rd and 4th (or overdrive ) are quite fine. If you go to the trouble of souping up any Cord and expect to enjoy the benefits you may end up with a disaster. They look magnificent when parked and are very enjoyable on the move.
I did have a short drive of a supercharged Custom Beverly in Italy. It was intoxicating listening to the blower but I was not game to push it as it was at night and it was raining.
The owner called out 80 when he was driving. I thought the guy was nuts as his two young children plus our wives were all piled in.ƒÿ▓
Just keep in mind "most problems with old cars are caused by the owners"!!!
CORDially Mike
mikespeed35Apr 17, 2026 Just keep in mind "most problems with old cars are caused by the owners"!!!
CORDially Mike
I thought I had covered the topic reasonably well.
Where do you get a new set of gears for a Cord these days?
The gearbox started off as a three speed but was then redesigned to include a fourth speed. The width of the gears had to be reduced to include the extra gear.
Cords had problems with the wheels, wheel hubs and suspension arms.
What exactly are you saying?
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
