Gary,
Push the shaft out. Sometimes you need to gently tap it out with a hammer and a drift. Once the shaft is out you can rotate the gears and they will fall out. Check the washers behind the gears for excessive wear.
Jim
Thanks Jim. I recently purchased the 4 bushings from George Arakenlian. Tonight I asked him just before I posted this question. I was mistaken thinking the ring gear needed to be removed first. Course that requires the steel rivets to be removed... Then probably heated up new ones before setting them... Big job for any home shop...
 
 
Gary Parsons
I removed the ring gear on my L-29 to put in high speed. Since the run out on the carrier is .002 I didn't want to beat on rivets and risk a change in run out so I bolted the ring gear back on. I used metric bolts as they provided the tightest fit. Used hard flat washers under the nuts with high strength Loctite and have had no problems in many miles. Just a alternative to think about.
CORDiallyMike
Mike,
I would caution anyone from using your method on an 810/812. You got away with it on an old, slow L-29 but you may not on a high performance car like an 810/812 (I know I'll hear about that comment).
 
Unless you drill and ream the holes and press fit in shoulder bolts there will be slop in the holes. You are relying on the clamping force of the bolts to hold the ring in position on the carrier. Given the number of variables in the surfaces and the forces involved on the ring and carrier, this method may result in the ring eventually moving(twisting) on the carrier.
 
Using rivets does two thing. First the shaft of the rivet is compressed and expands filling the hole completely ensuring the ring cannot twist on the carrier unless all the rivets start shearing - in which case you probably have other problems. Second they provide a clamping force that is not as apt to come loose as a bolt is. While a hot rivet is better since it deforms better and provides a higher clamping force as it cools as cold rivet will work if it done correctly.
 
On an 810/812 I have never found a loose rivet. Don Mates did tell me of a couple that were found "back in the old days"
Thank Jim. I have done plenty of cold rivet installation on steam turbine work. I had already decided if I was going to install ring gear rivets they were going to be done hot. Not cold. Of course run-out would still be a concern and be checked. Bolts were a thought but only as a last resort. You guys are great. Thanks...
 
 
Gary Parsons
Ask George Arakelian about how fast my L-29 is. I challenged him with his 812 S/C to a race and he was so scared he forfeited. I got his pink slip out of the deal.
CORDiallyMike
I was in an L29 once doing 77 mph on the speedometer before we took it off the blocks.
Pete
I've always regarded you as a friend Pete.
CORDiallyMike
What did it do with the wheels "properly" on the ground?
I have read when they are doing 80 things are about at their limit of their endurance.
All kidding aside L29 Cords need the high speed diff gears.
Mike has driven his more miles in the last 20+ years than anybody I know.
Mike, give us the FACTS
Pete
L-29's talk back at 50 MPH with stock 4:84 gears. Much better MPH 55or 60 with 3:91, and she doesn't talk back.
CORDiallyMike
 
 
 
CORDiallyMike
The story continues. I was unaware of these side n spider gears bushings in the beginning. I never was anything in the club Ayers trans booklet not on this site. So after taking the gears out with plenty of great advice, they just roll out once the pin has been removed. Then the real issues seen. The cone shaped bushing housing surfaces are well worn and need resurfacing. It takes a custom made cutter to clean it up. Not sure what that does to the to the clearances but we will see. Pics to come later but ANYONE rebuilding their trans ... This is a MUST DO ITEM... Replace and machine the cone bushing areas in the housing..
 
 
Gary Parsons
Gary, This is not a must do item. It is another item to check when rebuilding the transmission and to be addressed if needed. Most of the time the bronze bushings are fine. Some wear is allowed and OK. The bronze bushings are easy to replace.
 
If you need to resurface the iron parts you probably have other problems and should be looking at replacing the differential and pinion.
 
It is mentioned in the transmission manual to check this area.
 
Jim
Thanks Jim. I have inspected my ring n pinnion and they appear correct and fine. Please tell me what to look for in this area that may cause wear.
 
 
Gary Parsons
Thanks for the suggestions Jim. Pictures are nearly ready. From what I'm seeing it looks like low oil but never seeing this apart or anything to compare it too is a W.A.G. Wild ass guess.
 
 
Gary Parsons
When taking pictures I noticed the bad wear pattern and the chips on the inside of the gear. Am not very hopeful about finding a replacement ring n pinion gear. I have never set up these gears before on any car or truck. But have seen what proper wear patterns are. This pattern seems to have had the pinion set too sallow. I know the ring gear carrier can be set to either side too by the adjustments. I saved the shim pack found under the front pinion bearing too. Time to paint the gears and set the pattern I guess.
 
 
Gary Parsons
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.








