I wish you luck with the radiator cores. If they have good water flow, you probably will be OK. One of the problems with a Cord honeycone radiator core is that they canÔÇÖt be ÔÇ£Rodded outÔÇØ if they have restricted flow.
In the past IÔÇÖve had a company in Great Britain make brand new honeycone radiator core but it was very expensive (approx. $2400. with shipping). then you still had to solder the top and bottom tanks. IÔÇÖve heard Maine radiator also can make new honeycone cores.
I have used Brassworks https://www.thebrassworks.net/ and they have a core that is similar' date=' but to my knowledge you still need to go to England for proper Auburn and Cord core.[/quote'] 
This is true. I was down having lunch with Randy Ema today and we discussed this very thing. I recall about 4 years ago I offered a radiator to him for a customer but.. He said they are available in England for $1800.00.. Now Cliff noted they are $2400.00... Am wondering if copper has gone up that much or are they using gold as soldier... I will know in about a week if this one is cleanable because of the core tubes not being straight thru... 
 
Gary Parsons
I recently re-cored my radiator and went with the Modine tube & fin core, rather than honeycomb for several reasons. First, in judging either the Jamestown honeycomb or the Modine tube & fin are equally acceptable. Second, the honeycomb cores available from the place in England are not an exact match for the original Jamestown honeycomb. See photos below. I got quotes and they were VERY high (seemed like nearly $3000 but I didn't save the number). I may consider paying that much if it was an exact match but not for something just "close". Third, Modine cores are still made by Modine, and were purchased by Cord even if not installed before they ceased production of the 810/812s. Fourth, I tested the flow in both my original Jamestown core and an old Cord Modine core and there was literally no comparison. The Modine design is far superior, and given that Cords are known for overheating it seemed wise to replace my honeycomb with Modine. Especially since it is equally acceptable for judging and the alternative is to pay 3x more for something that still isn't totally correct. I did the same thing with my heater core.
 
Cores available from the current source in England:
 
Original Jamestown honeycomb pattern:
 
Old Modine tube and fin Core:
 
My finished re-cored radiator:
Wynn, What kind of flow rates did you get on the original radiator cores? Doc Flywheel did some testing years ago and I would like to compare your results with his.
JIm
How do you measure flow rate Jim. My Marmon 16 mechanic's manual gives it in gallons for a time period. The problem is I can't get enough flow from my hose to keep it full for the time specified.
CORDiallyMike
Mike, Flow rate is in GPM. Your house doesn't have enough capacity to check a radiator. The easiest way to measure it is to take it to a radiator shop which has the equipment to measure the flow. They also usually have a 2" water line coning into the shop so they have plenty of flow.
 
The only way I know to measure the flow rate at home is to rig up a tank (55 gal drum) to the radiator inlet and let the outlet free flow onto the ground. Then mark the tank at two levels so you know (or calculate) the volume between the marks. Then open the tank and start the clock when you get to the top mark and stop the clock when you get to the bottom mark. Then its a straight calculation to get the flow rate. Crude and messy but will give you a decent number.
Some radiators have a design to "slow the flow" thru them to increase the time needed for better heat transfer. In some mid to late 1980's ford diesel radiators the design is called dimple core. Every tube has dimples impressed into it to slow the coolant dropping or flowing down thru it. They are NOT cross flow radiators. These "dimple core" radiators were not successful as they were on the drawing boards. As to the actual design of the original honeycomb cores is not known to me. The shop I have doing my work is known for the work they do on many vintage cars. They do ALL the Duesenberg radiators. They know I have two of these Cord radiators and will get both to clean if they can clean the one I have there now.
 
 
Gary Parsons
The rad shops I have talked too have told me they got rid of their flow testers years ago. The way they test is" visual using experience" they say. My well pumps 5 Gal. a min., not near enough.
CORDiallyMike
George when 810 1586A arrived in Australia the radiator core was blocked full of gunk so I had to have the radiator rebuilt. Tom Georgeson told me to keep everything from the car and don't throw anything away. I often wondered about the core construction but never bothered to look at it too closely.Attached are a couple of pictures showing the twin core construction you mentioned.It is quite heavy.

Modine and Jamestown were original installation. Its been told to me the reason two different brands was not paying the bills. So another company was used they they didn't get paid. Eventually closing the doors forever... Sad thing...
 
 
Gary Parsons
The only place that does original honeycomb radiators is located in England. I recall something like $2800.00 U.S. dollars now. The wifey n I will be spending 6 weeks there next summer IF things are close to normal. Had to cancel this year....... I may if time allows look up the shop. That's one thing that interests me about going over there...
 
 
Gary Parsons
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.










