Curt: There are 3 sizes. I recently bought a set from Brian Joseph, but then found out that my existing bolts were larger diameter.
Must have been drilled and re-tapped at some point. Joseph has the bolt lengths on his website.
Brian shows four part numbers.
Didn't the originals have a 'W' on the head ?
Were original 810-812 head bolts cad plated or parkerized?
Curt I believe the Lycombing Cord engine had 3 different length head bolts. They had a "W" on them and they were Cad plated as per Stan. This "W" marking was not imprinted in the hex. It was above the hex. That makes it very difficult to re- produce but can be done just the same. Original head bolts will not work with the new heads that have the larger coolant capacity. I think original heads are available . They are new manufacture too. Not NOS..
 
 
Gary Parsons
I think he means on the top of the head.
I have quite a number of factory forged W ,GR8 SZ730 ( 3.5 inches long) head bolts that are cad plated. I am considering cutting some down and offering them to 810-812 owners
I feel confident that ALL 1931-1936 6&8 cylinder Auburns had 'W' head bolts. the 'W' is not stamped in the head of the bolt. It is raised.
I believe the technical term is embrossed . If 810-812 cords used the same 7/16 x 3.5 bolts, why wouldn't they used the same part. I have replaced many head bolts without markings or incorrect markings that were installed in the 40's-70's. I have three factory pictures clearly showing dark or black parkerized head bolts installed in 35-36 Auburns. I cannot speak to cad plated bolts on 810-812 Cords, but that is what I have.
I have seen both W and B2 markings on original head bolts on Cords. It is my understanding these were manufacturers marks. At the time there were no standards for markings or strength.
 
For length you need to measure the height of the heads and the height of the gasket. There are several different heights of the heads and thickness of gaskets, so you need to check any installation. You also need to check the threads in the holes as many times the first couple of threads have been pulled or the bottom threads may have corroded.
Thanks for this information Jim. I was looking at my head bolts for the original heads I have. I do not find any marks like you or I have posted. I recall something about some head bolts had no marks of any kind.It has been suggested that my car was built in 1936 but never sold. I believe I can show my car was built in 1937 somewhere around February or March. I have a smooth steering wheel and I have a metal patch covering the cowl filler area.Nothing on my engine shows any way the oil or coolant could be filled from the vent like the 36 cars had. The more I know.. The less I know...
 
 
Gary Parsons
Thanks for the info Jim. My car has the plate. I have posted a pic of it here some time ago. I was told eventually the factory removed that part of the cowl stamping so no patch plate was needed. I have never looked for this on 37 cars made later in the year than mine.
 
 
Gary Parsons
From a review of the 81/812 Engineering Changes notes your 1937 Cord Thanks for this interesting history on my car in general. Had forgotten my car was made or born in January of 1937. Once again the more I know the less I know about Cords. Still enjoy learning just the same. I think it was Josh Malks said once. Just when you think you have seen everything about these cars. something else comes up. Thanks.. 
 
Gary Parsons Model 812 Beverly was manufactured in late January, 1937. Cars with Serial Nos. 1746 and 31747 are shown in that time frame. The elimination of oil/water fill through the right cowl door began in May of 1936 per the same E.C. notes.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.





