

It appears to have both long shoes on this side. Many drum brakes use a long and a short shoe on each wheel. I'm not sure if our Cords are the same but its something to look into.
 
 
Gary Parsons

Thanks Gary. We are pulling the drum off the other side and I'm wondering if two longs were put on one side and two shorts on the other. I will report back with what we find.
 
A.J.
Also note that there is a direction the front or back shoe has to be installed. I believe the short shoe is installed on the front side of the drum because the back shoe actually is doing most of the work in stopping the car. The short front shoe drives the back shoe into the drum thru the rotation. If I'm wrong this forum has many more knowledgeable than me. But I try non the less. Remember, making mistakes is a way of learning. We are learning all the time. I think Jim Obrien said it best... All Cords are the same but they are all different.....
 
 
Gary Parsons

I have another set of drums and original shoes which I'm going to go find and compare. Today we removed the drivers side drum and it has the same shoe setup as the passenger side (with no squeak).
 
You are correct that the front and back look to be identical. While the original set I have seem to have a short and a long.
Hi AJ for new brake linings the rivet heads are close to the top of the linings usually the rivet heads are recessed quit a bit to allow for the linings to wear.
The rivet heads will be rubbing against the drum in no time.
I also noted there is no chamfer at the ends of the linings.
Not being familiar with the Bendix brakes I'm surprised to see a nut with a split pin holding the upper part of one brake shoe. I would have expected there to be spring loaded clips in four places.

Thanks guys. I should have noted that when the pictures were taken the we had partially disassembled things which accounts for the emergency brake bar and spring missing.
 
Terry - I'm eying the shoes suspiciously also. Digging out some original shoes tomorrow for comparison.
 
I will report results.
Hi AJ
Switch the shoes to the other side of the car and see if the squeak follows.
My brakes have the same bolt, nut etc. on the rears. Seems wrong but that is what they did on at least these 2 cars..
Pete

I noticed something different between your brakes and Petes brakes. On Petes brakes the adjuster spring is vastly different from yours. I believe your green spring is either on backwards or its the wrong type of adjuster spring.. I'm not able to remove one of my rear wheels and drums to get a picture for everyone to see.
 
 
Gar Parsons

Pete. Thank you for the picture. Gary I will investigate that. We leaning that it is the shoes (in particular the material) and perhaps it is directional and one of them is backwards?
 
We have chamfered the shoes and I'm going to test it out again hopefully on Monday. We would contour them but as you guys have noted some of the rivets are close to the surface.
 
I'll let you know what happens. Old cars are fun.
AJ looking on the Internet for Cord Bendix Brakes I found the attached pictures which are in the Forums somewhere.One shows a front wheel brake assembly and the other shows a rear wheel brake assembly.You appear to be missing the springs either side of the wheel cylinder and the lower spring is not making contact with the brake adjustment star nut. The spring stops the star nut from moving out of adjustment.Note The rear spring metal covers. See diagram below pictures.Good luck with your investigations.
After looking at Terry's pic, the green spring at the adjustment wheel appears to actually be one of 2 return springs, that should be attached, one end to the pin at the top of the backing plate, and the other to either the front or rear shoe to pull the shoes back away from the drums, when you take your foot off the brake pedal. The spring that is suppose to be at the bottom, holding the shoes together and keeping the adjustment wheel from turning , except when a spoon is used to tighten or loosen the pads, is not shown in your pic.
You should take an inventory of all your springs and parts to make sure you have all the parts shown on Terry's pic and assemble them as shown.
I don't know about you, but sometimes us older folks can benefit tremendously by taking lots of pics or making diagrams of what we are starting to disassemble, before we disassemble it. Then we can refer to that info as we attempt to remember how it goes back together..
Exactly... I have been taking before pictures for years now. It sure has helped me more times than I like to recall.
 
 
Gary Parsons
This picture clearly shows a short front shoe. Terry are your brakes Lockheed or Bendix? I believe I recall you telling me these are Lockheed brakes on your 36 car.
 
 
Gary Parsons
Hello Gary. Yes my early production 810 Cord has the original Lockheed brakes. The pictures I found on the Internet in this topic show the later type Bendix brakes.
Lockheeds are retarders, Bendix are stoppers.

Guys, my apologies for sending you on a wild goose chase. I took those pictures after the partial disassembly. All the springs are there correctly.
 
Good news!!!! I just drove about 10 miles and zero squeaks or lock ups. What fixed it was chamfering all the edges including the sides. So the pads were the problem.
 
Bad news was 3 miles from home it started sputtering. I do not believe vapor lock as I threw the electric pump on and it didn't completely smooth out. But a separate problem for another day.
 
I jinxed myself when I thought "Wow, this car is fantastic and finally fully sorted!".
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.



