

currently Ebay has a listing for two complete shifting arms with exactly what you want... But I can tell you what condition they are in. Doug at ACD parts in Oklahoma probably has this. I bet Jim Obrien or George Arakelian also can help you out. They are shakers n movers in this area of the 810 812 Cord cars... Jim has written several articles in the ACD news letter about this particular area.
Terry is a wonderful source of expertise in this area as you already have found out.
Gary Parsons

Gary ParsonsJul 29, 2025 currently Ebay has a listing for two complete shifting arms with exactly what you want... But I can tell you what condition they are in. Doug at ACD parts in Oklahoma probably has this. I bet Jim Obrien or George Arakelian also can help you out. They are shakers n movers in this area of the 810 812 Cord cars... Jim has written several articles in the ACD news letter about this particular area.
Terry is a wonderful source of expertise in this area as you already have found out.
Gary Parsons
Gary, I could not find them.
The issue with the 3D printed ones is that require a lot of finish work. I think a good used one is a better idea.
The re-engineered selection switch clip that Auburn Cord parts was selling is a god send. Every car needs one of those.
ACD in Broken Arrow doesnÔÇÖt currently have any available- any other ideas on where/who/contact info to purchase some?
I have an original switch available. Send me a private message for the details

Mike is a good guy. That is the best way to go.
Yes Adam is correct. My son Joe prints the bodies, has the contacts laser cut, made forming dies to shape new contacts and assembles these. I add a new 10 wire cloth covered harness and a new pencil and rotary disk. We originally made the bodies for those people who had a switch with a broken body. Many did reuse their old contacts, but it takes careful adjusting contacts and careful assembly with proper insulating washers and brass rivets. Often many have either soldered an insulated terminal to a rivet or left out these washers. Our preferred method now is to have you ship us your complete shift arm and we assemble and bench test unit. You then can reinstall in your steering column and add plug. If you want a one piece wiring harness, we need your steering column tube. This has been a labor intensive project to say the least. As you can imagine, this like many other projects we have done, profit is questionable and that is why people like Stan found it hard to make money.
Pat Leahy

37beverlyAug 5, 2025 Yes Adam is correct. My son Joe prints the bodies, has the contacts laser cut, made forming dies to shape new contacts and assembles these. I add a new 10 wire cloth covered harness and a new pencil and rotary disk. We originally made the bodies for those people who had a switch with a broken body. Many did reuse their old contacts, but it takes careful adjusting contacts and careful assembly with proper insulating washers and brass rivets. Often many have either soldered an insulated terminal to a rivet or left out these washers. Our preferred method now is to have you ship us your complete shift arm and we assemble and bench test unit. You then can reinstall in your steering column and add plug. If you want a one piece wiring harness, we need your steering column tube. This has been a labor intensive project to say the least. As you can imagine, this like many other projects we have done, profit is questionable and that is why people like Stan found it hard to make money.
Pat Leahy
That is great Pat! Yes, our issue was a piece of solder on the insulating rivet which unbeknownst to us was a conductor. 100 hours later we figured it out.
Working on my own here in Australia I ran into problems with the Gear Selection System after soldering a new wiring loom to the gear Selector Switch.
I followed Henry Portz's test procedure but could not get the desired results.
I then decided to test the Gear Selector Switch on its own to make sure it was ok.
I made up the attached wiring diagram which alsancle posted previously. I have also added the written test procedure.
With this in hand I was able to discover a fault in the rotating part of the switch which was quickly rectified.
I believe my Cord had travelled over 300,000 miles before I restored it. I had to bore out the cast housing to fit a slotted bush for the sliding pencil. There was a lot of slop in the mechanism which had to be eliminated first.
I'm having problems adding the written test procedure ................... I will have to come back to this.
Test Procedure.
Note. The colours of the wires and their numbers were taken off the overall wiring diagram for the gear selection System, see the last attachment.
Basically disconnect all wire at the Interlock Switch and Solenoid valves.
For The Sliding Contacts
Disconnect the battery and clutch switch.
First supply power to the red wire and test lights with alligator clips to the black, green, yellow/black and red/green wires.
As you go through the switch movements the various test lights should come on according to each gear selected as well as neutral.
For The Rotating Contacts
Supply power to the green/red wire and test lights to the brown, blue and white wires.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.








.jpg.6bf00a88a0b58d85b3a252fcceb569e0.webp)