

You and I think a lot alike. As I mentioned in the other string I just bought two of them. The Westchester that I recently bought has a water pump leak and I figured having an extra one in case the Phaeton does the same would be a good idea. As you say, how long will they be available. I have not installed mine yet but there are one or two posts on the AACA forum that recommend the kit, here is a link:
https://forums.aaca.org/topic/313235-812-waterpump-rebuild-who/
 
One person said the car ran cooler after installing the kit. I am looking forward to installing one to find out.
 
Bill
I had no idea Henry's daughter was still running and keeping his business open for sales. I still need to go up there just to enjoy looking at the Henry shop. I admired Henry and his work for over 45 years.
 
 
Gary Parsons
For those that have not found it yet here is the website address, it does not seem to pop up near the top of searches, at least the ones I have done:
 
http://www.portzcordz.com/index.shtml
 
Bill
Thank you for the pictures Terry, I was wondering what an original impeller looked like and what metal it is. It appears from your picture that the impeller is cast iron, is that correct? I received an extra water pump with the Westchester that I purchased earlier this year and it had a tag on it that said "maybe rebuilt". Looking inside the shaft is very shiny and the impeller looks to be made of brass however I only count 8 vanes. If the original impeller was cast iron then maybe there is hope that my extra water pump is indeed rebuilt. Of course who knows when.
Bill


We have our kit now. While rummaging through my dad's Cord parts I found an old pump and got the bright idea that I should rebuild that one and have it ready to swap out. When I got it home and started looking at it I'm thinking I see why it didn't get used. It looks like the shaft housing has been welded back on. Rethinking my plans. See pictures. Thoughts?
If the section was welded back on properly it should be fine. Check it by putting the bearings and shaft in and tighten down the cover. If the shaft spins freely they you are fine. If the shaft binds then the piece was welded back on at an angle. If the misalignment is not too bad then it can be corrected with some machining.
 
The other key to rebuilding the water pump is making sure the seal surfaces are lapped in properly. It looks like you have the modern cartridge seals. Did you also get the ceramic seats? If so make sure they are installed 90 degrees to the shaft.

Thanks Jim!
The seals in the picture where in the box with the old pump, I didn't take the rest of the stuff out of new kit but will go check and give what you are suggesting a try!
 
Also, I seem to recall there is some machine work that is necessary to make the new shaft and impeller work? There were no instructions with the kit, so maybe I'm imagining that.
Sadly this is a mess. I was a welder for 30 years in a major public utility company in California. This can be repaired but its going to be very difficult. This newly found crack will require grinding out. Then clamped back to the original position. Then welded in. Cast iron is tuff to weld so most times its braised. But new roda are available today. Once this is welded you will require machining to straighten out the seals so they are inline with the shaft. May be best to locate another housing. Its a gamblers choice. Ask yourself if you were on the dark side of the moon... On a sunday night after 6 pm what would you do to get home....
 
 
Gary Parsons
AJ
I'd check the pump which is on the car now. Since you are so close, why not send the cracked pump housing to Frank to see if it can be stitched ?

AJ
I'd check the pump which is on the car now. Since you are so close, why not send the cracked pump housing to Frank to see if it can be stitched ?
 
Mike, since the spare pump rebuild was a convenience idea to simply make the swap quicker, rebuilding the exsisting pump is probably what we will do unless I find another decent pump housing. I've never paid attention so I don't know if they are unobtainable?


I'm also going to rebuild my pump. I am contemplating powder coating the unit. My question is do you think doing the inside and outside would hurt anything? I would hope the smoother it is the better the flow would be.
 
Robert L Hauser
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.









