Hello Michael Ehrlich of Maryland,
What you are reporting about starting problems with this Cord is totally alien to my experience during my period of custodianship of the machine. Even in an unheated Missouri garage in dead of winter I was able to start the engine with minimal cranking. Based on what you have described it is my opinion you may have a fuel flow problem. The carburetor on the engine at the time I owned the car was a conglomeration of the proper EE-25 Stromberg unit. The base casting was properly marked but the air horn , float chamber and choke parts were not totally correct. With the original cam driven fuel pump you would not have fuel pressure/flow to the carburetor except while starter cranking the engine. Though I am totally enamored with the Cord Models 810/812 I am basically just an amateur Model A Ford shade tree mechanic so take my comment with a grain of salt. Contact experts such as George Arakelian and Jim O'Brien to get reliable answers. Good luck with your trouble shooting.
Hi Michael.
I had similar problems with my Cord so I fitted an electric fuel pump for priming the system. The pump is switched on for 10 to 15 seconds to prime the system then switched off before starting. It certainly made the difference.
The electric fuel pump is the low pressure type. I found that on steep hills the engine would start to falter so I then switched the pump back on which brought the engine back on song. Some guys have the electric pump running all the time but I only use it for priming and occasionally on steep hills and leave it running on the mechanical pump normally.
Jack, Terry,
Thanks for your comments. And yes Jack, I only noticed this within the past 2 months. Originally she started up just fine. As for the electric fuel pump, certainly easy enough to add. Do most folks plumb the electric pump in-line prior to the mechanical pump, or is there usually some sort of bypass plumbed in? And any recommendations on an electric fuel pump?
 
-Michael
Electric fuel pumps should be as close to the gas tank as possible as they push, not pull fuel. I feel a gear rotor pump is best as they don't have a dia. thus no ethanol issues. I think you have another issue besides with fuel delivery you should diagnose before you just add a electric pump. 3 to 7 minutes of cranking is way too long. Carb. should be primed way before that.
CORDiallyMike
I have had similar problems of long cranking after setting.
The carb is empty and needs to be filled. Instead of an electric fuel pump, I have changed the fuel pump . Looks exactly the same but it has a hand "tickler" at the bottom so that you can manually pump fuel into the carb prior to cranking. Works perfect
Thanks Mike, I agree it's way too long. Figure I have all winter to work it out. I don't plan on just adding an electric fuel pump to fix the problem - I'd like to understand the root cause and fix that first. That said, if the electric fuel pump can fix the issue, that may be what I resort to.
-Michael
Hi Michael,
I'll put my 2 cents in. First the car didn't used to have this problem so what has changed? Has any work been done on it lately?
 
Second it doesn't sound like an empty fuel problem. If the fuel is draining out of the carb. it wouldn't take as long as you describe to get the fuel up to the carb and once you did the engine would fire up and run, not cut out several times.
 
It sounds like you need to tart looking for another problem. First I'd check the timing, Second the points. Then the electrical system. Do you have the proper voltage to the coil, are you getting a good strong spark to the spark plug, etc.
 
This one may take some digging but I don't think the problem is getting gas to the carb.
 
Good luck and let us know what you find.
Jim
I agree with Jim's comments "What has changed with the car in recent times?" When I said I had a similar problem with my Cord I should have explained that it needed extra cranking before starting but not the length of time you mentioned.
The electric fuel pump just speeded up the process. Maybe the valves in my fuel pump need replacing?
Another Cord out here needed excessive cranking to start it. One of the guys checked it out and found a loose wire at the ignition switch. After tightening ................ instant starting.
So the point is you will need further checking.
Ron Hewitt is out of the business of rebuilding carbs & pumps. He sold the business of rebuilding to Chris's Carb shop.
Contact:
Chris's Carb Shop 7718 N. Main St Dayton OH 45415 877-498-2272 or 937-890-0970 kits carbs chriss.carb.shop@hotmail.com
Thanks to everyone for your thoughts.
 
I took out the fuel pump and sent it to Then & Now Automotive to be rebuilt. Hoping to get it back and installed by the end of the month.
 
Now that it's out, is there anything else that folks typically address?
 
-Michael
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.

