Hi Michael,
The main problem is you neglected Geneva for too long, Cords do not tolerate that. :-)
First don't do what Gary suggested, you are apt to create more problems then you will find.
You need to see what the shifting is doing or not doing. Open the hood, have someone start the car, depress the clutch and move the selector switch into 1st gear. Then use a volt meter and check the second wire from the rear (black wire) on the solenoid bank(located in front of the radiator on the right side). You should have 6 volts there. If there is no voltage your problem is probably up in the shift switch.
If you have 6 volts you need to pull the front bumper and transmission cover and see what is happening. First question the cross shift moving to the left side. If the cross shift moves to the left check the the third or fourth wire from the front (blue wires) on the solenoids and see if you have 6 volts. If you don't have 6 volts the cross shift switch may not be making and may need adjustment.
Try these and let us know how you make out.
Jim
Ok, quick update.
 
First of all, I've done almost nothing to help figure out the problem. Last evening I did look for the wiring harness connector near the master cylinder and found it easily. I also found that the large connector just hangs in the breeze - is that normal or is it usually attached to something? And while I did not unplug the connector, I did notice that the upper shell of the connector can be really easily slid up the wires, and inside the shell of the connector housing it is extremely greasy. Is the grease in the connector body normal? Anyway, after sliding the connector housing up and getting my fingers all greasy I slid it back down and decided I would tackle it another day.
 
And this morning, just for fun, I started up Geneva and she shifted into reverse and first with no problem. So maybe I successfully jiggled something. Guess I'll look this weekend.
 
Thanks for all your help - I'll keep you posted.
 
-Michael
Congratulations on Geneva shifting into 1st and reverse today. My thoughts are you still may have issues in this plug area but please DO NOT work on it with the battery power connected. I'm really not versed in the shifting electrical from the steering column down to the transmission.Am not sure is turning off the engine ignition switch kills all power to this.
The plug you slid the top half clear of in supposed to be fastened to the floor board firewall by a clip. The clip "may" be available thru Henry Portz. Sadly he has recently passed on but I think his daughter Cathy is handling the business now. I have not talked to her since the West Coast Meet a few months ago. I viewed his web site and saw some under dash wire harness will be available sometime in Sept...
Quick update. I have still done nothing other than "fiddle" with the outside of the plug that first time and it continues to work. Out of sight out of mind. I'll move on to other things.
 
And for what its worth, I learned long ago to disconnect the battery whenever I work on nearly any car. I was given a surprise once when working on a late model car with a ratchet in the engine compartment. While removing a small bolt, the handle of the ratchet contacted the metal fan motor housing, and surprisingly completed the battery circuit. 4th of July right there in my garage. The car had two identical fans. One housing was grounded internally. Apparently the other fan housing wasn't and was sitting at +12V just waiting for me and my ratchet. Both fans ran fine. I ended up wrapping the offending fan motor housing with a silicon tape so I wouldn't accidentally bridge it to ground again.
 
So now, I disconnect the battery. And it's very to do on Geneva - there is a disconnect switch right at the battery to stop the 1 Amp draw I seem to have when everything is off. Still haven't figured that one out. I did check the voltage regulator to see if any of the points had welded together on the breaker portion, but all was fine with the regulator - in fact it looked brand new on the inside!
 
-Michael
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.




