As to getting started what is your Serial Number and what is your engine number ? I too have an early Westchester with Serial No 810 1586A. The filler caps in the cowl attach to the oil and water pipes under the hood. I have attached a couple pictures of an early Westchester that I saw in Auburn in 2011. Have you contacted Ron Irwin the Cord 810 812 historian in California ? He may be able to help you with the history of your car. Welcome to the ACD Club, where are you located in the world ? I am in Australia.Regards,Terry Cockerell
As to getting started what is your Serial Number and what is your engine number ? I too have an early Westchester with Serial No 810 1586A. The filler caps in the cowl attach to the oil and water pipes under the hood. I have attached a couple pictures of an early Westchester that I saw in Auburn in 2011. Have you contacted Ron Irwin the Cord 810 812 historian in California ? He may be able to help you with the history of your car. Welcome to the ACD Club, where are you located in the world ? I am in Australia.
Regards,
Terry Cockerell
 
 
thanks for your reply.
 
i am based in Mumbai, India
details of the car are as below
serial : 1900 A
engine : FB 1176
body no : C 90 - 997
 
 
 
have no access to the newsletter yet, dont know why
i think Ron Irwins details are mentioned there
Where did you find or purchase your car ? It looks to be very original under the hood although in need of restoration. Do you have a copy of Josh Malks book Cord Complete ? It is advertised in the ACD Newsletter and is the best place to start understanding a Cord. You asked about gear box modifications. You will need to install a heavier thrust ring. Stan Gilliland at AC Parts in Kansas can help you with this item. I am actually restoring my car at present although I had it on the road for five years. They are wonderful cars and a delight to drive. Cords were assembled in a plant called "The Central" in Connersville, which is located south of Auburn. I have attached a picture of the plant but sadly most of it is gone now.What is your home email address as it will be easier to send you copies of technical information ?I have listed Ron's postal address as he is not into computers. Ron Irwin. 18319 Grayland Ave, Artesia, CA 90701 - 5737, USATo order a copy of Cord Complete contact
Where did you find or purchase your car ? It looks to be very original under the hood although in need of restoration. Do you have a copy of Josh Malks book Cord Complete ? It is advertised in the ACD Newsletter and is the best place to start understanding a Cord. You asked about gear box modifications. You will need to install a heavier thrust ring. Stan Gilliland at AC Parts in Kansas can help you with this item. I am actually restoring my car at present although I had it on the road for five years. They are wonderful cars and a delight to drive. Cords were assembled in a plant called "The Central" in Connersville, which is located south of Auburn. I have attached a picture of the plant but sadly most of it is gone now.
What is your home email address as it will be easier to send you copies of technical information ?
I have listed Ron's postal address as he is not into computers. 
Ron Irwin. 18319 Grayland Ave, Artesia, CA 90701 - 5737, USA 
To order a copy of Cord Complete contact 
thank you in advance for the data.
Welcome to the Cord club. Your engine appears very complete. Please do not exchange that generator for any other Autolite generator. Yours appears correct and very rare. It has the TC (two charge) voltage regulator on top of it but the knob is not correct. It looks like a radio knob and they too are rare so don't just throw it away. Ebay has many close examples of these TC regulators and not very expensive to buy just for the top knob.
That hole in the firewall was the easy approach to changing the engine timing chains. Best repair is to replace the complete piece top to bottom. Stan may have this piece too.
Horns are another rare piece as is the air filter. Your carb looks like the correct EE15.
Rebuilding the water pump can be difficult. the rear cover is hard to remove without ruining it so be careful when prying it off. Use plenty of heat on the case and some Aerokroil penetrant. Its sold by Kano Labs in the USA. I have used it for nearly 45 years on any stuck nut, bolt or assembly.
Door handles are not available or the trunk latches.
Headlight lense with the reflectors are very rare too but a member in Europe has made reproductions and they are very nice.
What condition is your instrument panel? The cats eye cigar lighter is very costly if you do not have one. The red is mostly used but they came green too..
I have rebuild all my gauges, starter, carb, and fuel pump along with several other items. I have posted most of the before and after pics on this forum hoping others can learn from what I have done. I'm no expert but do know a few things about these great cars. Best of luck finding the parts you need too. This forum is a great place to get help restoring these cars.
Hi,
 
There are several posts on disassembling the water pump on your 810 Cord. Advance-search the topics for "water pump" in the 810/812 Cord categories for information. Take the info to heart as it is easy to break the casting.
 
The main thing is to be PATIENT in getting it apart. Lots of penetrant, lots of patience.
 
--Tom
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
































