Thanks for your informative reply. Someone had marked 4 2 R on the transmission cover. Thanks to you I now understand where all of the gear positions are. Your point about an unwanted electrical signal is well taken. I wonder if removing the clevis pin connecting the vacuum cylinder rod to the shift lever would be the simple answer. However,there might be a danger of that rod hanging up on the disconnected lever and bending something if the rod received a command to move while disconnected.
Thanks again, and I hope others will chime in. I feel like I will enjoy driving the car a lot more if I know that I can deal with a no shift condition with confidence.
With the key off you don't h
 
 
 
 
 
 
 
 
 
When making a manual shift at the trans with the key off you don't have to worry about electrically activated unwanted shifting later on. Nor is it necessary to disconnect the shift cylinder clevis when doing a manual shift. For such shifting at the trans with the key off put the e brake on and a full length clutch stick in place and first determine whether the trans is in neutral or some gear. You can tell by the left vs right, front vs rear position of the lever to which the clevis is attached. To get to a desired gear the lever must be first moved to the mid point between the frontal position and the rearward one. Then it can be moved sideways as required, then forward or backward into a desired gear. Low and reverse are spur gears and may not be aligned to engage easily. Mine must have been a terrible shifter in days of yore. The trans cover was trap-doored for easy and probably frequent access for manual shifting.
Rick,
 
If you are out and the Cord quits shifting your best bet is to get it shifting again. It's extremely rare that you can't get at least some of the gears. Worst case is that you only have 2nd and 3rd which is fine to get you home as long as you don't need to back up or start on a steep hill.
 
If you loose all your shifting it's usually the clutch cut out switch. You can jury rig this with a jumper wire and have the shifting "hot" all the time. Just DON'T PRESELECT!
 
1748S's description of the shift pattern is not quite correct. 3rd gear is directly below second in the center of the pattern. You need to have JK Howells diagram of the shifting wiring. This shows the pattern and the wiring so you can trace things out. It is in the transmission manual which is another must have item for any Cord owner.
 
Jim
Many thanks to all who have posted. I don't plan to drive my Cord long distance. 90% of my driving will be taking it out in the evening within 25 miles of home. The rest will be on CCCA type tours where the longest day might be a total of 200 miles with multiple stops. So, if I could totally fix the problem great, but my main interest at this point is just knowing that whatever the failure might be, I would have the knowledge to quickly get it in 2nd or preferably 3rd gear and get out of there - home or back to the car hauler or hotel. Then I could troubleshoot at my leisure. I do have the transmission manual and wiring diagrams.
Thanks again!
Gary - Regarding not quite correct - you said to pull the cross shift to the passenger side and to the front for 3rd gear. Neutral is between 2nd and 3rd gear, all you have to do is pull the lever to the front of the car. If you pull the lever to the passenger side all you can do is push it rearward into 4th gear.
 
Regarding the synchronizer release pressure - it is critical to the proper operation of the transmission. Use a bathroom scale and an arbor press. Put some shims under the ring of the synchronizer and use the arbor press to push down on the hub. Watch the scale and see when the synchronizer releases. For the 2/3 synchronizer you need to check it both ways, they will always be a little different. Adjust the springs until you have the correct release pressure. Note the factory spec on the release pressure is after 100 shifts so if the synchronizer is rebuilt you need to shift it numerous times to "break it in" before measuring the release pressure as it will change during this break in period.
It might help understanding the Cord shifter system if you look at Tom Hussey's " Cord Transmission Simulation " 2012 - 2013.
George.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
