Hi Pete,
 
Glad to hear the Cord is driving and shifting OK. Are the CV joints clunking when you are going in a straight line or when you go around a corner? They always clunk when going around a corner and did so almost from new (a few hundred miles). If they are clunking going in a straight line then you have other issues.
 
I'm not sure what type of modern CV grease you have. The original CV grease was a thick liquid (which I'm sure leaked all over the wheels). You need something on the thinner side so it will work it's way into the joints and is tacky to stay there. Normally going around the roads up here in the Northeast the wheels get turned enough to move the grease around as long as it isn't too thick.
 
To grease the inner CV joints you have the fittings on the housing. The one on the right side should have an extension on it to get the grease point up above the solenoids. The one on the left is just a plug in the housing. If the inner CV joints are dry you will hear the most God awful noise coming from the front end and thing the whole front end is falling apart.
 
For the outer CV joints you have to remove the wheel cover (hub cap), remove the cotter pin holding the nut at the center of the wheel. In the middle of the shaft there is a slotted screw that has to be removed (behind the cotter pin) You can screw in a zerk fitting or piece of pipe with a zerk fitting on it and put the grease in that way with a grease gun.
 
The next question is usually how much grease do you put in. The answer I got when I started in this Club was the same amount that leaked out (smart ass old timers). There is a 1/8" pipe plug on the housing (we are talking about the outer CV joints now) if you remove this plug you fill up the joint until the grease comes out. Note the wheel as to be turned hard in one direction to have the plug exposed to the joint and not covered by the inner bell.
 
Jim
Interesting story to go with this thread. Back in 2000 when Doug Johnson and Bob McEwan were making there cross country trip in Bob's Cord they had an issue with the joints.
 
After driving for several hours in a straight line some where down in the south west, they started hearing a noise in the front end. It kept getting louder. After a while they decided that the grease in the outer CV joint must have moved out of the space around the balls and was makeing the noise due to lack of lubrication. To try to test this theory and get the grease back into the area around the balls Doug (who was driving) started weaving across the road. Being this was a wide open empty road this was not a problem...EXCEPT out of nowhere a cop saw then and pulled them over.
 
Now first picture Doug trying to get "Wee Robbie" to hide all the empty beer cans on the floor of the Cord (Bob was just trying to stay hydrated going across the desert) not to mention the half full one in Bob's hand while he was stopping. Then trying to explain to the officer that this 70 year old car was front wheel drive (everyone know the first front wheel drive car was the '66 Toronado) and they were just trying to move the grease around in the CV joints.
 
I would have paid good money to have a video of that!
Hello all: about a year and a half ago, I took apart the whole front end with emphasis on getting the C/V joints to stop leaking. We removed the front fenders, hood, and the engine with the trans still attached.
Replaced all gaskets and seals with modern. Thoroughly cleaned inner and outer joints by taking them all apart, right down to the balls. Found two balls with cracks/gouges in them and replaced with better used ones. My mechanic friend recommended "marine" type grease which is used in boat applications. It is a bluish-green color. The old book recommends one pound of grease in each joint, which is the modern one tube. With the joints back together, except for the grease, I held and rotated the joints and moved the shafts as my mechanic friend filled every nook and cranny. We made sure a full tube was used for each joint. Reassembled. No drips, runs, or errors! A very slight clunk heard at very slow speed making a very sharp turn. Tim is a happy Corder!
Thanks for the inspiring information Tim. The way you "moved the joint" is exactly what I had planned to do.
Can you tell us whats seals you had and what was leaking? Were these older leather seals? I still have 2 new large seals for the outer joints with the 4 screws that holds the cover in place to the housing. I do not plan using them either. I think of them as museum pieces.
I should have notes on the seals and gaskets used, and will post them when I find them.
Tim.
Hi Tim,
 
I'd love to your notes on seals and gaskets. Thank you in advance.
 
--Tom
Hi Tim, 
I'd love to your notes on seals and gaskets. Thank you in advance. 
--Tom
I have all the seals and gaskets for my Cord. I was interested in what seals and gaskets were leaking on your car.
Gents-Good friend Carlton Zeigler gave me some special grease (per Don Mates) he had and told me to mix in two tablespoons of STP and mix thoroughly to each quart to get proper consistency of lemon murang pie filling. SP? He had a pump with which I filled the inner knuckles and Voila! no more clunk clunk! (I thought I'd filled them 5 years ago when I filled the outer knuckles). But thanks for all your suggestions!
 
Pete Rhoads
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
