Hi,
 
Be sure to obtain the ACD Transmission Manual book from the ACD store. It's the best ten bucks you will spend on this job.
 
One strongly recommended item to do when rebuilding the tranny is to replace the 3rd gear thrust washer with a thicker hardened steel one. This requires some machining work to be done. Read about it in the Forum or in the Manual.
 
--Tom
Like Tom says get the transmission book before you start, it had a step by step procedure for pulling everything apart. It's been a long time since I read it (I've done too many of these I know what to do by heart) but if I remember if very good.
 
When you get to the engine and transmission pull them out in one piece and separate them on the floor. It's much easier.
 
Also when rebuilding the transmission send it to someone who has done several of them, it's worth the money to have it done correctly. The transmission is critical to having the Cord run and shift correctly and there are tricks that aren't in the manual. Plus after you have done several you develop the "feel" for how it goes together and what is right. Since you are in Michigan I would send it to Lee or George.
 
Jim
I don't recall reading any information how to remove the engine and trans. That sure would be a nice addition to this forum. I helped install our engine and trans way back in 1966 I think. I was very young back then. After I took position of this car in 1975 I got it running and started a restoration. Removing the engine in involved. The front wheels come off but the brakes and backing plates can stay on the housing. The brake hose must be removed from both wheel cylinders. The steering linkage must be removed from both housings. The large nut on the end of the universal joint shaft must be removed from both sides. If you choose to leave that connected then you can but its going to be a little heavier to handle all those parts when the axles come out of the inner universal joints.The drift pins in the inner universal joints must be driven out. Some cars have only one pin and others have 2 in each universal joint. Now the really fun part. Both the top and bottom king pins must be removed along with the bearings and the dust covers. This can get messy too . When the top and bottom king pin bearings are removed you can pull off th brake backing plate and the housing from the drive shaft. Of if you left the large not still on the end of the shaft remove it along with the drive shaft. Do the same with the other side. Now to get the engine and trans out as one piece you can just remove the 4 bolts connecting the trans to the forward trans mount. Or remove the spring u bolts and lift out the trans and the mount as one piece. Now for the rear engine mounts again you have choices. REmove the center bolts or remove the bolts that connects the mount plates to the engine block. I have seen it done both ways. Bag and tab the motor mounts too. There is an upper and lower plus there is washers involved. I can send you a pic of what the mounts looks like if needed. Of course there is plenty of trans linkage and wires plus vacuum hoses to remove. Also the sheet metal that needs to be removed is lots too. The hood comes off along with the louver fence. Exhaust comes off too. Remember the battery grounds at the forward end of the trans and the cable on the starter. Gas line disconnects too. Don't know when you want to drain oils and coolant but thats another good idea to plan ahead for. Removing the radiator and the support is easy. Just bag and tag parts. Might want to take pics with a cell phone too. nothing better than a pic of what it looked like. Sometimes the carb linkage can be a problem so take pics of that too before removal. I'm sure I have left out plenty but the last time I did this job I was about 25 years old. Am now 63 and forget things all the time.. I make notes too but I misplace them so that does not help.. I need an assistant "watching me"...
Here is a good picture of what you need to remove to allow the trans and engine come out as one. At the end of the axle is the nut that holds the brake drum and axle to the hub. Its up to you if you want to leave the brake drum on or not.
Hi,
 
I am losing sleep over that thrust washer that I am sure my dad and brother did not upgrade back in 1955. I mean, who knew back then that such an improvement should be made?
 
1509A's engine and transmission assembly are currently out of the car. Can this shaft be removed and the parts upgraded without separating the transmission from the engine? The other side of the coin is that 1509A will never see more use than parading and local pleasure trips, and presumably that thrust washer can be expected to last through a lifetime or two of such light use.
 
Decisions, decisions. Any input?
 
--Tom
Tom,
 
Get some sleep. if yours is already done and you are only going to do light driving it will be fine. The original thrust washer will last especially if you are careful on the shifts. I think George has been running the original for years in his phaeton. I've pulled apart several transmissions with the original thrust washer still intact (working on one now).
 
But they do fail, So while someone is rebuilding a transmission it's worth while to upgrade and remove a known problem. I figure I never know how the car will be driven in the future. Most start off as trailer queens or very light driving. but if they ever get an owner like me, they get driven hard. I'd rather be safe.
 
Also to answer your question you can not do this modification without removing the transmission and disassembling the entire upper shaft.
 
CORDially,
Jim
Hi,
 
Thank you, Jim. You have given me a precious gift: peace of mind.
 
 
--Tom 😁
Some years ago, at a West Coast Meet, a club member from Reno, NV had a handout on removing the engine and transmission. I have a copy but we just moved and everything is a jumble. You could contact this fellow, Adrian Greive whose contact info is in the ACD Directory, and see if he could provide you with a copy. If he can't, then get back to me and I'll see if I can locate my copy. As I remember it was pretty complete and would be helpful.
 
You'll have to remove the oil pump and shifting assembly from the front of the transmission to remove it. Just take it slow and be sure everything is unhooked. You don't want to damage the lines for the engine temperature or oil pressure.
.
I have re-read the transmission removal steps in the Cord Transmission manual. This is very good and walks you thru the process with lots of tips. Again my recommendation is to pull the engine and trans as one unit. Trying to pull the transmission and leaving the engine in the car may be fine for someone that is 25 and in very good shape. The transmission weighs somewhere around 130 or 140 lbs (and has been getting heavier every year). Trying to slide that back 3/8". rotate it 180 degrees and then pull it out is asking for trouble.
 
One more point to note is that once you slide the trans back the 3/8" off the dowel you MUST support the transmission at all times, you can not let it rest on the input shaft. If you do you run the risk of bending the input shaft (I have seen several of these bent). It's much easier to do it on the floor where you can slide the transmission straight back. Also if you think pulling the transmission is by itself may be hard, try putting it back in!
 
Gary - if your mind is like mine... you are in deep trouble 😁
On the question of do it or don't do it, I'm dissenter...I'd advise you to DO the thick washer conversion now, while the tranny is out and the pricy guts are presumably intact. The cost is chump change compared to a possible catastrophic event. I experienced the splined washer breaking in my Cord back in the dark ages when I was a fuzzy cheeked lad and Cords were $300 cars. Fortunately I knew what was happening because I had a mentor who was an early Cord expert and he had warned me about it. Had I not known it could have been a disaster. As it was, everything was useable afterwards, except for the washer of course. Here's the symptom; when the washer breaks the sensation is that a phantom passenger has reached his foot over and put it on the brakes. This is the trans. trying to go into 2 gears at once. It lets up, then does it more. Don't shrug it off, it'll cost ya! I was one block from home when it happened, but the day before I had come from 120 miles away!
I also had a modification done by the late Tom Pendergast to the synchronizer ring to prevent it from malfunctioning and allowing the spring loaded balls to pop out and mangle the gears. I haven't looked, but that too should be in the trans manual and can be done for little cost. .
Happy Memorial Day to all and a special remembrance to all that have served in our Armed Services and those that have passed.
I also have found this day to be a Happy Memorable Day. The engine/transmission in 1752A finally been pulled. It put up a fight until the end and as my wife stated there is a foreign language of engine pulling that she had never heard of. After a little bit of negotiating the leaf spring, struggling with the front drive axles, etc., it is resting on wooden blocks in our garage raised floor area for final disassembly with the engine headed to the engine rebuilder west of here and the transmission heading a little south of Grand Rapids for its rebuild. It is one greasy mess (greasiest of all engines I have ever worked on) and I have to comment that even after emptying all the fluids prior to pulling, the transmission just kept pouring out more oil than ever imagined. So, far, the trans axles look really in good shape, transmission gears look good, no metal in the oil, etc. The engine was a known problem with a head gasket seal blown and one piston frozen. Other wise it is not in bad shape.
 
I am curious what the weight is of both components together, and our them separated. Any ideas or facts, figures on this?
 
Happy Memorial Day and Happy Memorable Day.
Bill
 
Other than looking really cool Tom, why did you leave your engine block green?
Hi,
 
LOL--in 1955, rust prevention consisted of zinc-chromate primer and a hard enamel paint. I'm not sure Rust-O-leum had been invented yet.
 
The green color came about because that's what my dad had most of a quart of!
 
--Tom
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
