Hi Tim,
 
Interesting info. If this car is in fact a 36, and not the 36 serial number plate attached by someone to a 37, then the mystery of the location of the taillights is even more engaging.
 
Here are more pix of this car. It appears to have been converted to 12-volt with an alternator and what looks like a ceramic ignition resistor on the right firewall. It has modern driving lights and turn signals on the front. There's what might be a coolant overflow canister in front of the radiator.
 
http://i595.photobucket.com/albums/tt36/trp3141592/1542_p22_l_zpsj12ohofx.jpg
 
http://i595.photobucket.com/albums/tt36/trp3141592/1542_p6_l_zpse7xxqnvb.jpg
 
http://i595.photobucket.com/albums/tt36/trp3141592/1542_p21_l_zps4cegzz0v.jpg
 
Members--any more info ?????????????????????????????????????????????
 
--Tom
Its get more interesting all the time. I'm not seeing the radiator catch can in the pic but I do feel that black can is oil for something. See what looks like a brass level indicator on the side. Also noted the solenoid pack does not have all the wires connected to it. Looks like only 2 wires connected to it. Also whats with the ball valves on the vacuum lines fromt e solenoid pack to the shift cylinder???
The finally I see an interesting place to collect enough exhaust heat to make the auto choke function. See it off the drivers side exhaust pipe just inboard of the fence. Might very well be converted to 12 volts too. Still a very nice looking cord.
Gary, the ball valves are used to restrict vacuum on the main shift cylinder.
This is said to reduce clunks while shifting, something I have yet to try.
Was also puzzled by the missing wiring on the solenoids.
Hi,
 
Since this car has apparently been converted to 12-volt, I wonder if there is a bank of modern relays that are functioning in lieu of the original relays. I considered doing this myself, but with sealed 6-volt relays. If so, they are not shown in any pix that I have seen.
 
I like the ball valve idea for the vacuum lines--I think 1509A will have that added feature when I reassemble it this spring and summer.
 
--Tom
Please take another look at the solenoid box, I think all the wires are there. It appears the bullet connectors are in place and the wires are bent at 90 degrees towards the rear of the car. if you look close you can see one at the rear of the solenoid box bending towards the drivers side of the car.
 
Also I think the horns are correct. Remember there were three different horns used thru the production run.
Hi Gary,
 
Since you mention it, I HAVE seen the brass elbow fittings with the drilled, tapped, and inserted bolt to restrict vacuum. In fact, in my treasure trove of 1000's of downloads regarding re-assembling my Cord, I found a picture of them. I think these were on EBay. I had forgotten that I had the images. I wonder what additional tidbits that I thought were a good idea I have forgotten also!
 
http://i595.photobucket.com/albums/tt36/trp3141592/gear%20shifting%20restricter_zpsbnx8spec.jpg
 
These adaptations look easy to perform, but I DO like the ball valve option. I'll decide when it's time to make the decision: Lowe's is 3 minutes away, and they have the ball valves available.
 
Cords: Curiouser and curiouser and even MORE curiouser!
 
--Tom
Hi Jim,
 
I believe you're right. I zoomed up the image to 600% and it's evident that the wires are there, parallel to each other, and then sent off at a right angle to the driver's side.
 
Good eyes, Jim!
 
--Tom
Hi. I own 2593A, and it lives here in Midland Michigan. Be assured, all the wires are on the solinoid array. The car is 12 volt, but the shift system runs on 6 volts through a dropping resistor. The tail lights are a quandary however, as we noticed they were in the " wrong position" in the first photos we saw before buying the car. I plan to look into the trunk lid to see if there are plugged alternative holes. I was just into the tail lights to put brighter bulbs, and nothing was revealed at that time. There might be some 1937 parts in the back, but I don't see any sheet metal grafting on the car.
The shift control ball valves were difficult to adjust, and I bought the drilled and taped elbows at Auburn. They work well, and the ball valves are gone.
I have been cleaning up wiring and I stealthed in a Pertronix ignition.
I installed a vacuum brake booster (sorry purists...). It sure makes me a lot more confident at 70 miles per hour. At least it is mounted low on the right hand side and is not easy to see.
This week she is getting a new clutch and a set of 4 new (1970s) wheels, then going to the body shop to get the wrong mirrors removed and to fix a couple of blemishes in the paint.
I would love to find an original heater, but the one in it works very well and looks decent. Any ideas???
Dale Martin
Hi Dale,
 
What a joy to have your information on this car! I'll be very interested to hear what you find inside the trunk lid since I can find no images of another Westchester that has the outboard taillights.
 
Since your car is an 810, presumably it has Lockheed/Wagner brakes. That in itself is plenty of justification for a vacuum booster!
 
She is a beautiful car, and it sounds like the changes are functional improvements (of which I approve, not being a purist!) For sure, when 1509A eventually hits the road, it will have improvements also.
 
Thank you for your post!
 
--Tom
The black metal can is a radiator overflow catch. It wears black wrinkle paint and is not pretty, but it works.
I would love To have two of these cars. One, a nice driver like this and a completely orginal , totally accurate to the original build. That would be nice.. Right?
Dale
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
