Gooood Day Pete
You shoukld quite horsing around trying to find this house and have Cat Tail cast you one..
mikewestMar 2, 2026 Gooood Day Pete
You shoukld quite horsing around trying to find this house and have Cat Tail cast you one..
quit horsing around
I remember reading in an old ACD Club newsletter that the original bell housings which I assume were cast aluminium distorted a bit when they warmed up. This lead to gear change problems and the introduction of a clutch brake. Not widely publicized but getting a new bell housing cast would give the opportunity to add some more stiffness.

Re-casting 10 of them is a possibility but it might take 25 years to get rid of the other 9.
Terry, never heard of a clutch brake in a Model J transmission. It does get harder to shift when the transmission gets really warm though.

Terry CockerellMar 2, 2026 I remember reading in an old ACD Club newsletter that the original bell housings which I assume were cast aluminium distorted a bit when they warmed up. This lead to gear change problems and the introduction of a clutch brake. Not widely publicized but getting a new bell housing cast would give the opportunity to add some more stiffness.
The problem is not it flexing, the issue was the exhaust manifold heating one side of the engine up more than the other...thus the exhaust side expansion made the transmission go out of alignment. Experienced Model J people surface the bell housing so that when fully warm, everything is square. Works great. Been there, done that.
ED this is very interesting. I did mention distortion and should have included elastic distortion as the problem disappeared when the drive train had all cooled down.
From what you said the bell housing is machined to give a slightly tapered shape.
How many thousands of an inch are removed?
I had a temperature sensitive problem with the cross shaft on my 810 Cord that nearly drove me NUTS. When it warmed up I could only get First, Revers and Fourth gears.
Removing the sheet metal cover to conduct tests when it warmed up I could consistently get all gears.
I tried all sorts of tests. Eventually when I went back to the Transmission Manual written by Sid Ayres I noted a statement regarding any movement in the cross shaft keyways will result in a loss of syncronization.
Removing the cross shaft then fitting the levers and keys and doing a bench test by clamping the shaft in a vice and using a pipe lever I discovered movement. The root cause was the main vacuum cylinder hammering the keyways. A new shaft was made and fitted plus flow restrictors were added to the vacuum cylinder lines. It has worked consistently since then.
AJ I can't remember which newsletter had the story. I have a large pile of old newsletters that were given to me by an older Australian member who passed away last year.
If you have one of the Newsletter CDs you could do a search. I do remember a clutch brake being mentioned.
ED I assume from what you have said about resurfacing the bell housing that when the engine is cold the gearbox is out of alignment and that it lines up nicely as the bell housing heats up.
Why wasn't the exhaust system insulated in that area?
Or was that tried??

My J has a clutch brake.

Hemi JoelApr 14, 2026 My J has a clutch brake.
What is the transmission?

It is the 3 speed original transmission.

alsancleApr 14, 2026 What is the transmission?
Here is a pic where you can see the shaft and the operating lever.


alsancleApr 14, 2026 What is the transmission?
Here is a pic where you can see the shaft and the operating lever.


I'm personally not a fan of clutch brakes. Maybe I've never driven a car with one properly adjusted? Or I just can't drive.
That is interesting. Have never heard of a Model J with a clutch brake before.

AJ, you have driven a Model J with a clutch brake, you just don't know it. I recently removed the one from 565. Just have to install a new cover.

Was a clutch brake standard equipment?
I've worked on two Duesenbergs and neither had a clutch brake at the time. I have no idea how correct either car was.
I am STILL looking for a J Duesenberg BELL HOUSING
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
