
Do a search of the forum. It could be the plug in the harness at the bottom of the steering column, interlok switch, selection switch, diaphragms, etc. You need to methodically go through each part of the system.
Do you have any wiring diagrams?
.jpg.28193d292b31d9ae3582da56aec9c0cf.webp)
This happened when it first came back from the body shop as well where it sets so long and I can't remember where I got the drawing that showed me which connections to jump with the engine running and I did that and it all started working again well then we parked it and let it sit for a while and now it's back to that same condition and I can't find that drawing. It won't go to second third no problem I'm back to neutral and like I said it pulls to the left and to the right when you put it in low or reverse or four but it won't engage and it's exactly what it did when it came back from the body shop. The first time I did all that went through the interlock switch the connection that the steering column everything then somebody said try jumping these poles and I did and it started working.
Terry CockerellAug 18, 2026 Do you have any wiring diagrams?
I do thank you though.

GasWorksGarageAug 19, 2026 This happened when it first came back from the body shop as well where it sets so long and I can't remember where I got the drawing that showed me which connections to jump with the engine running and I did that and it all started working again well then we parked it and let it sit for a while and now it's back to that same condition and I can't find that drawing. It won't go to second third no problem I'm back to neutral and like I said it pulls to the left and to the right when you put it in low or reverse or four but it won't engage and it's exactly what it did when it came back from the body shop. The first time I did all that went through the interlock switch the connection that the steering column everything then somebody said try jumping these poles and I did and it started working.
Here is my wild ass guess. If it will move laterally between 4th and 1/R but not stop in the middle I would look at the plug first. Make sure it is nice and clean and making a good connection. Then I would look at the interlok switch. It is not picking up the middle location.
I goes to neutral I have checked everything I can think of
Thanks
GasWorksGarageAug 20, 2026 I goes to neutral I have checked everything I can think of
Thanks
There is a series of tests that can be done with lights hooked up to key points that was put together by Henry Portz. Do you have that?
It test the overall system.
I developed my own test procedure for the Gear Selector Switch on its own.
The only way to find the problem or problems is to test each part in the gear selection system separately.
With all wires disconnected from solenoid bank and cross shift do the following test:
Test column shift switch Test #1
Connect power to red wire:
Gear shift in first.  Green & black
Gear shift in reverse.  Green & black
Gear shift in second.  Yellow with black tracer
Gear shift in third.  Yellow with black tracer
Gear shift in fourth.   Yellow & red with green tracer
Gear shift in neutral. Yellow with black tracer
Test column shift switch Test #2
Connect power to Green with red tracer:
Gear shift in first.  Blue wire
Gear shift in reverse.  Brown wire
Gear shift in second.  Brown wire
Gear shift in third.  Blue wire
Gear shift in fourth.  Brown wire
Gear shift in neutral.  White wire
Electrical test for cross shift switch:
Disconnect wires from cross shift switch
Disconnect Main shift cylinder from cross shift arm
             2nd & 3rd
Arm in center position: continuity between:
Green with red tracer & yellow with black tracer
White & green & red with green tracer
               1st & Reverse
Arm in right position: continuity between:
Green & green with red tracer
White & yellow with black tracer & red with green tracer
                   4th
Arm in left position: continuity between:
Green with red tracer & red with green tracer
White & yellow with black tracer & green9
Electrical test for main shift cylinder switch:
Disconnect Main cylinder shaft from shift arm, remover pin
Disconnect White, blue, and Brown wires from Main cylinder at solenoid box
Connect to white wire and blue to meter and check for continuity. You should not have continuity at center and one side. Connect White and brown and you should have opposite result.
Great test procedure, Pat.
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
