If I were you Greg, I would contact the guys in the ACD club that have these early cars. They are listed in the back of the directory. 
There was a time I owned a 13 Caddy. I promptly joined the HCCA  and contacted  every one that had a 12-14 .  I found what I needed.
Thanks for the advice  Curti.  I will dig out my HCCA roster and see if there are any listed. The ACD club is definitely more interest in the later cars , but I am sure there is a fringe element that is involved with early Auburn's.  Probably quite a bit of overlap with the HCCA. More brass era needles in the haystack.
 
Greg in Canada
 
Hi Greg, i suggest you contact Ken Findley in South Surrey. he is pretty well connected with Brass era cars on the west coast. You are also welcome to swing by the shop some time to talk about your project. I am big into ACD cars but have only played with the mid thirties cars. I am always interested what other guys are playing with. especially in my own back yard.
 
Kirk
I'm not familiar with Auburn,  and the only 1914 4-40 listing I have is not conclusive as to the engine...
Assuming it is a vendor engine, do you have its ID (maker and makers engine model)???
If a T-H, model # should be letter (N, O, T) or letter + number (T17, T18).......
Rutenber did produce at least one 4cyl 41/2x5, if the Auburn Rutenber had same b/s; d'you know which Rutenber was used??--per old parts catalog listings, they seemed to have much greater penetration as a supplier, than T-H, but old parts catalogs are not definitive sources...
Hi Kirk, thanks for the advice. I have already talked to Ken, and a number of the Pacific N.W. brass era guys over the last 15 years . And the previous owner was well connected to the brass scene for at least another 10 years without much luck. I have come to the conclusion there is probably not an engine or parts for this engine in this geographic area. The previous owner found and acquired quite a bit of what's needed but no crankcase , sump, cams, timing gears , cam followers, or water pump. But these parts came from the Midwest as far as I know. And yes I would be very interested in seeing your set up, your Boat tail is a jewel ! I will be in touch next time I have some days off. I work an oddball 12 on 6 off rotation.
 Hi Bud, the engine I am after is a Teetor Hartley. It is not described as such in Auburn listings but that is definitely what Auburn used in at least the 1914 4 Cyl. cars.  I am not sure if was a 1 year only offering or if some of the earlier large engine Auburns used it as well.  Most of the bigger 4 Cyl. Auburns used Rutenbur engines as you suggest, from about 1911 to 1913.  I don't know what model designation Teetor called this engine. It seems to have been used in a number of cars, American, Auburn, Pilot, Staver Chicago and probably one or two more. But they seem to be quite hard to find. As far as I know parts from any of the monoblock Teetor 4's would work, but I have been told the crankcases destined for American Underslung cars have the mounting bosses cast higher on the crankcase. I have yet to see a good photo of an American Teetor crankcase to confirm this is the case.
 The engine was built in at least two sizes , 4 3/8 x 5 and 4 1/2 x 5 .  But apart from pistons and possibly the block casting  all the remainder of the engine is the same.
  If you happen to have the current HCCA Gazette , Jan / Feb 2017, on page 42 there are several photos of an Auburn in the Pioneer Auto collection , Murdo SD. that has this exact engine. As well the 1914 Auburn sales brochure illustration also shows what is clearly a 4 cyl.Teetor engine . Auburn must have been happy with them as a few years later they used Teetor 6's in several models .
 
Greg in Canada
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
