

Startix has nothing to do with the charging system. If you must, disconnect the reference wire from the generator to the startix. It wonÔÇÖt change anything. Look at your generator field coils and armature. Also, donÔÇÖt assume a modern reproduction cut out is correctÔǪÔǪ.or good. Too much Chinese junk being sold. ┬áIt should be a simple fix.
Thanks AJ,
I am a member of the ACD and used to frequent that site until they "improved " it. I have not been able to access since.
I'll try again.
Ed,
I know what you're thinking. I also feel that I may be overlooking something on a simple system. I think the wire from 
the generator to the Startix is intended to operate a lock-out solenoid when the engine fires. To know I can delete this wire for diagnostic purposes
is helpful. I've always felt the Startix was a solution looking for a problem. If I continue to fire the car using the Startix and switching to ignition to run,
can any damage be done?
I have had the generator on and off about six times. I have checked fields, armature, brushes and removed all paint from non-exposed areas to benefit ground.
I have also had this unit in a local shop. Have installed original Autolite as well as chinese junk cutouts.  I install the generator, adjust third brush and charge is good. Typically 
I fire the next day and nothing.
I remain baffled.
Thanks for the replies,
Dennis
 

Dennis,
 
If you didn't mention the Startix I would have said cut-out with a 75% probability. 
 
 
Thanks,
Two separate cutouts. When it refuses to charge 6.4 volts at battery wire and 1.7 volts at generator. Has to be internal but out of ideas. 
Dennis
Make sure 1 of the brushes is not hanging up because of weak spring. Had that happen on my 8-98 and after "rebuilt" did it again only to finally find the brush hangup.
Thanks Pete,
Just pulled it again and visually all brushes are seating good. 
IÔÇÖll check closer tomorrow.
Dennis

Check battery voltage and voltage at both sides of the cut out. You can pull the cut out cover off and manually close and open the points to see what is happening. Something is strange..and if your using a Chinese DVOM, toss it in the trash and buy a Fluke.
Ed,
6.4 at the bat.  terminal. 
1.7 at the gen. terminal.  
Have had Autolite and Chinese cutouts installed. 
Cutout manually depressed results in major discharge. 
Blue point VOM. 
Strange for sure. Definitely internal but certainly not visible. I may try to induce a little heat and test. What do you think. 
Thanks,
Dennis
This is when it is not charging 
6.4 and 7.5 volts at 16 amps when it decides to cooperate. 

Did you check the shunt inside the generator? Did it pass a bench test? 

Is it running a 4000 series Autolite cut out? Nos or modern repro?
Thanks Ed,
No shunt. three brush generator. Passes all static bench tests and dynamic tests when it's working.
Autolite 4021 and chinese replacement cut-outs have been installed. When it's acting up there is not sufficient output to engage either cut-out.
I am convinced it is internal but don't understand the inconsistent charging and can't find a reason.
Dennis
 
Does the battery run down if it isn't charging? Does it ever take to charging once running? Have you got a badazz double throw down battery in it? Have you loaded the system by turning on the bright lights and hitting the brake to make it all engage? AMPS vs VOLTS. Several variants of cutout relays are adjustable, making that old mid-40s motors manual for 5 bucks off the swap meet table a valued resource. YOU are there, we are not, so this was meant to trigger a "Hey wait a minute..." about the challenge. And, I do hope you'll let us know. I'd bet coffee you're here because most topics never follow thru with what their solution was. We're all rootin for ya...
Thanks Highlander,
The battery does run down when not charging. Standard 6-volt battery of the proper group. I have loaded
the system with headlights, brakes, etc. I also have a Sun Vat40 to induce load. Keep in mind when working this generator performs 
as it should. Otherwise, no output. I am going to investigate the insulation on the field coils again. I have to believe it is somehow related to 
heat. 
I will surely let the group know what I find. 
Dennis 
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
