

Could be old gas???

plkDec 18, 2025 Could be old gas???
No, the tank is full of super fresh 100LL. Its good that my other hobby is old airplanes.
Add 4 oz Marval Mystery Oil per 10 gallons of gasoline. It keeps the valves from sticking. It can also be added to the crankcase as directed.
Eric
Given that running products through the fuel system hasn't worked yet, I think you are left with some degree of disassembly.
Either the head or the manifold.
With the manifold off, you can get directly to the valve stems and guides. A bit easier than taking the head off ( 8 nuts plus three on the exhaust pipe vs 27 head bolts, draining the water supply and removing the dist ).
I used a syringe with some tubing to squirt some Kroil around each guide. Could also try some carb/ throttle body cleaner as well. Downside is, you don't get to assess the valve condition and you really don't know if you have solved the problem without bolting everything together and seeing what happens!
This method might result in some dripping into the crankcase but I don't think that shouold affect things, both products are pretty volatile.
I have no idea if this is going to work because I'm a little ways from an actual running vehicle .
Wow, they really went to town with the bedazzler didn't they. ƒÿä Is that fuel pump polished or is it actually chrome plated? Valve side covers too!
Brad
Try MMO before going to the trouble of a tear down, it works for many and is delivered constantly while the engine is running.

JFranklinDec 18, 2025 Try MMO before going to the trouble of a tear down, it works for many and is delivered constantly while the engine is running.
In paragraph three of my thoughts I explained "... I have run Marvel Mystery Oil through the fuel as well as in the oil pan and that has not cured it."

bradsanDec 18, 2025 Eric
Given that running products through the fuel system hasn't worked yet, I think you are left with some degree of disassembly.
Either the head or the manifold.
With the manifold off, you can get directly to the valve stems and guides. A bit easier than taking the head off ( 8 nuts plus three on the exhaust pipe vs 27 head bolts, draining the water supply and removing the dist ).
I used a syringe with some tubing to squirt some Kroil around each guide. Could also try some carb/ throttle body cleaner as well. Downside is, you don't get to assess the valve condition and you really don't know if you have solved the problem without bolting everything together and seeing what happens!
This method might result in some dripping into the crankcase but I don't think that shouold affect things, both products are pretty volatile.
I have no idea if this is going to work because I'm a little ways from an actual running vehicle .
Wow, they really went to town with the bedazzler didn't they. ƒÿä Is that fuel pump polished or is it actually chrome plated? Valve side covers too!
Brad
Brad, yep this car was restored when everyone liked chrome -- it was done by Dallas Winslow -- but it has held up well enough that I left it alone. If I ever have to restore the car I would put it back to stock. The good news is that it shows well at most concours events but it is also why I have never brought her to Auburn.
Sorry I missed that. I have added it straight into a running engine through a vacuum port.
The root cause is probably varnish/carbon buildup on the valve stems. MMO (to me) is more like an upper cylinder lube, and would have limited benefits for your problem.
I have had good success over the years with ChevronÔÇÖs Techron. It contains a polyetheramine that is designed to loosen carbon. The only downside is that it can contaminate the oil, and some sources recommend changing it afterwards, but I never have. IÔÇÖd give a try.
I think you have answered your own question as far as why. Off and on the trailer, don't drive faster than 30MPH, 50 miles in last three months. It takes 35 miles to get a car to operating temperature. Sounds like you should drive the car more miles to keep the sticking from happening. The other valves are probably not far behind. I know that is hard when the car is being shown. I had the same happened with a L-29 Cord, but after 60,000 miles. I tried the solutions suggested above, but ended up removing the head and cleaning valve stems which were carboned up. Just one persons opinion though. Good luck.
CORDially Mike

mikespeed35Dec 19, 2025 I think you have answered your own question as far as why. Off and on the trailer, don't drive faster than 30MPH, 50 miles in last three months. It takes 35 miles to get a car to operating temperature. Sounds like you should drive the car more miles to keep the sticking from happening. The other valves are probably not far behind. I know that is hard when the car is being shown. I had the same happened with a L-29 Cord, but after 60,000 miles. I tried the solutions suggested above, but ended up removing the head and cleaning valve stems which were carboned up. Just one persons opinion though. Good luck.
CORDially Mike
Mike thanks for your opinion -- I have heard that logic before. I have only owned this car for a couple of years and I am still learning. And, I guess if the penalty for my usage is that I have to clean the valves it ain't the end of the world. The funny thing is that the Lycoming engine in my airplane did the same thing.
Eric LipperDec 18, 2025 Brad, yep this car was restored when everyone liked chrome -- it was done by Dallas Winslow -- but it has held up well enough that I left it alone. If I ever have to restore the car I would put it back to stock. The good news is that it shows well at most concours events but it is also why I have never brought her to Auburn.
Don't get me wrong , I think its a great conversation starter. I've looked at so many photos of these engines and yours just is out there. I think you should start a 'factory chrome' story as per the paint - that for $50 the factory would chrome any engine part you wanted. The looks you'd get would be priceless! Its the water outlet that gets me everytime. I mean of all the pieces one could chrome- even the blingy L29 didn't chrome that part!!!!!
I'd leave it as is , part of the car's history .
I think Lee has identified the issue with MMO and Mike is on point with a factor being the less they are driven , the more they stick. My previous owner did a rebuild of some sorts ( don't have details so I don't know what kind of valve work was done - if any ) then started the car every couple of months for 15 minutes , I'm thinking that is why the valves are sticky.
Or not!
He was also running without a thermostat which means its going to take longer to warm up. I'll try to exercise restraint and not go into my usual cooling system sermon!
Brad

Run the hell out of the car.the varnish will melt away. Im not a fan of adding oil to the fuel. Get VP-C9 fuel for long term storage. Spraying a fuel injection cleaner like a Snap On motovac unit uses by spraying into car at half throttle will degum the top end if you do it a few times while hot.

When I have seen the sticking/unsticking problem come and go it was because of bent valves. The valves just barely touched the pistons and slightly bent them which made it very easy for them to bind. But not always, car would run great for a long time and if it sat for too long, valves would stick.
But that was an overhead valve engine. Not sure how you bend them on a flat head.

Not calling it solved but figured what the hell and I would flush a bunch to cleaner through the vacuum system. Did a full can tonight and made a ton of smoke. Drove the car a couple of miles and never got a stuck valve. More news to follow because I am going to mess around with her more tomorrow.

edinmassDec 19, 2025 Run the hell out of the car.the varnish will melt away. Im not a fan of adding oil to the fuel. Get VP-C9 fuel for long term storage. Spraying a fuel injection cleaner like a Snap On motovac unit uses by spraying into car at half throttle will degum the top end if you do it a few times while hot.
Thanks Ed. You are generally right on everything. I tend to agree that there is probably nothing wrong because the problem showed up at idle going into a trailer. More news to follow your lead. I am going to run my motovac on it tomorrow. PS. Bought a really cool Packard and I am loving that too. The difference between a 1931 Auburn and a 1938 Packard Straight Eight is mind blowing.

Here is a little bit of a report. I ran my motorvac on the engine for a while and then pushed some valve cleaner aerosol through the vacuum port that runs the windshield wipers. I don't want to announce success yet because this car tends to surprise me but I drove the car about 30 miles today (after cleaning) and the #6 valve never hung up. I let the car cool down tonight and I am going to take the car through another heat cycle tomorrow. The best fun was the 1972 Opel GT that I we have been restoring made it to three miles today. All good progress.

I have to askÔǪÔǪ.Is the Packard red? ƒÿç

Well guys a blind squirrel finds a nut every once in a while. For me I circulated some Motorvac carbon cleaner using the Motorvac system and then drove the car about 15 miles over two drives today and another 15 miles yesterday. Weather was perfect and the car was purring -- I suspect that the intake system really must have had a lot of carbon. Unfortunately before I became the caretaker of this car I have no clue how the car was maintained. After cleaning, the #6 valve never stuck during any of these drives so I am going to assume that the problem is now solved. In my experience with the issue it always seemed that the valve would stick within the first minute or two of operation. Fingers crossed and thanks for everyone's advice. At the end of the day it seems that edinmass hit it on the head. Frankly, I forgot I had a Motorvac in my shop but I bought one because the Ferrari's tend to carbon up -- handy tool. @edinmass
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.







