

Eric,
 
My response over on the AACA before I found your post here.
The old packing that I have sitting on the bench looks to be 3/8 x either 1/4 or 5/16.
Mine is apart on the bench because I have an 'idea' that I can replace the packing with a lip seal AND get a ball bearing in the 'nose' AND still have it look original.
I'm probably outsmarting myself and asking for trouble.
Randy has been doing this a lot longer than I have, I'm sure he'll set me straight !!!
AACA comments
The original was a rope packingPacking generally used now is square  graphite impregnated packing,
You'll need about 3 rings. Its a 3/4" shaft and the OD of the housing is 1.500  so I would try 3/8 x either 1/4 or 5/16".
I wouldn't  use anything with teflon, especially if the shaft has been replaced with 316SS !!!! Lots of  opinions against Teflon if you search but others experiences may vary.
Cut the ends of each ring  at 45 degrees , not 90 .
Don't over tighten!, not much more than hand tight and you will  have to adjust as the new packing wears in .
Be prepared to accept some drips, they  always drip and its better to have some drips than over tighten and wear the shaft. 
Hopefully, the shaft is in good condition and the 'nose' bearing isn't too worn . This is the biggest design flaw of these pumps, The 'nose' bearing is a plain bronze bearing with no lubrication. The more wear in the bearing , the faster the packing starts leaking again.
 

You stated the nose bearing has no lubrication. Yes it does, that is the function of the grease cup  Fill it with water pump grease, install it, turn it one turn on a regular basis like 500 miles. A small tin will last you a life time.
George . Retired auto mechanic.
Morning George
I wondered about that too and it looks like it needs more grease; use water pump grease.
Pete
George
 
I was trying as best I could to differentiate the bearings in the water pump .
My view is that there are are actually two bearings in these pumps ,
1) The main bearing pressed into the casting . Agreed that is lubricated
2) The packing nut or 'nose' bearing . That one receives no lubrication
 
Most late pre-war and post- war  water pumps have the shaft pointing to the front of the car  and the covert at the rear.
When I look at the pump out of the car , I always think of the cast cover as the "rear' even though it points forward when installed in the car.
As you know, the 'front' of the pump where it is driven by the generator actually points to the rear  of the vehicle when installed.
 
I was trying to figure out what to cal the packing nut bearing. I probably should have stuck with 'packing nut bearing' instead of making up 'nose' bearing.
Sorry for any confusion.
 
The packing nut bearing receives no lubrication and does suffer substantial  wear.  I have three examples on the bench with various stages of wear , some of the wear is quite substantial ( 0.030") .
I think ( always dangerous!) that the increased wear in the packing nut results in shaft 'wobble' and  premature failure of the packing and wear on the pressed in housing bearing.
 
If only someone could find a way to fit a ball bearing in the packing nut.
 
Brad
Before I retired, one item I looked after at my job was the large heating and air conditioning pumps. They had the square graphite packing on each end of the shafts. When adjusted properly they were supposed to leak I think 6-8 drops per minute. If they did not leak the packing would heat up and score the shafts. The water leaks lubricated the packing. The Auburn pump may have different requirements though.
Tom
I should add that after the new packing is installed start the engine and gradually tighten the gland nut allowing the packing to conform to the shaft while it is leaking water so it will not burn and score the shaft. I emphasize to tighten the nut slowly and let it sit for a while and then tighten it a bit more and let it sit. Eventually it should seal so there is almost no water coming out.
Tom
Thomas
 
I think your observations would apply to the Auburn waterpump as well.
The used shafts I'm looking at on the bench are all heavily scored where the packing runs. I think people get overly enthusiastic in their efforts to stop leaking quickly and entirely .
Our expectations for these old cars have been set by our experiences with modern where any leaking is unacceptable. I also have a Model T which, as the saying goes, if it is leaking it isn't running. Even these Auburns with a properly functioning Bijur system are going to drip on your floor.   It's a total loss chassis oiling system!
I've followed lots of waterpump trials and tribulations with my 1925 Buick buddies ( two packings per pump,   more fun!) and they all seem to agree that a few drips as you've described is the best. operating condition  A zero drip condition is only temporary!
That said, I'm a little OCD and drips drive me nuts so I can see where Eric is coming from.
 
Brad
 
Craig
 
Do you happen to have any photos of how you did that you could share?
 
 
Thanks Brad
No photos, but it's National number 470954.
As I recall, I pulled all the packing out and polished the shaft. Then I bottomed the new seal, probably put some goo on the outer surface, and held it in place with the packing nut. I won't say who gave me the idea and the part number, but I didn't come up with it. Been holding just fine for nearly 4 years now.

To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
