The ticking noise is in the first cylindar. It sounds like a lifter. What else might it be?
Also, does it require removing the head to adjust the lifters? I have never done this on a flat head motor before. I have done it on a V-8 and on a 5 cylendar Audi.where I could remove the valve covers.
Do I remove the water jacket cover to get to the tappets?
 
The lifters are under the intake and exaust manifold. I would suggest going on the ACD Museum website and buying a manual before you start.
Maybe there is a youtube video on line, you might check. The lifters are on the opposite side of the motor as the water jacket side cover. You don't remove the head. There is a valve cover under the exaust and intake manifold. The lifters can be adjusted without removing the manifolds ,but it is difficult. Buy the manual! Hope this helps. CORDially Mike
Hello
Where did you get the manual? Can I buy it online somewhere?
 
My engine is in good condition, but you never know....
Thank you.
 
Regards from Germany
Michael
Hello Jim
Thank you for the link. I will order one.
 
The repair of your engine should not be a problem for a qualified engine repair service.
The engine of our car was rebuild by
http://www.petervangiersbergen.nl/
This was done before we bought the car. The engine runs smooth without mechanical problem or noise.
The only problem was the gasket of cylinder head.
Because of aluminium head on cast iron block and the length of the engine it is a little bit tricky to seal the cylinder head.
The change of the gasket was done by
http://www.car-niederrhein.de/
Both companies are not specialised in Auburn or US classics, but they were able to keep the engine running.
I am shure that you will find a qualified engine shop which is specialised in classic cars in Indiana.
 
In order to fix all other items which i can not repair myself, we visit an Opel sales and repair shop.
(Opel is an old german brand, was part of GM and belongs to Stellantis Group now) This dealer is specialized in repair of classic cars of all brands and help us to keep the car on the road.
Here in germany you will not find a repair shop specialised in Auburn. With the help of the ACDClub members and a classic car repair shop and patience you will manage all problems with your car, as we do here.
regards from germany
Michael
UpdateAfter disasembling the engine, the noise is a result of a faulty babbit on the first cylindar.Other issues:A short in the distrributor rotor sparking to the block.Excessive play in the distance between the crank shaft and the sides of the piston rods.A very loose timing chain.I've found a very competant mechanic here in Indiana who has a complete machine shop. He is busy but made room for me. Thanks!Finding the correct parts is going to be a challenge, but what isn't when one has an 88 year old car?
According to the mechanic, the crank and cam shafts are in excellent condition. It may be that that the piston rods are not original and too narrow for the space, which allowed the pistons to slap on the cylindar walls, thus making the loud internal noise.
He has sent out the rods to be re-babitted and to have additional material added onto the sides to compensate for the excessive movement. I see the thickness of your babbits compared to mine. Quite a bit of difference. I will speak to my mechnic about that..
This Babbit job was not done correctly but... Its VERY DIFFICULT to understand how this rod was machined in the last 88 years. No telling if it was compromised in the past.  It appears to NOT be installed inline with the crankshaft but who knows what may have been done. As for adding Babbit to the sides to make up the gaps I strongly advise not to do that. Looking at Pete's original rod there is nothing Babbited to the sides of the rod. As to the Babbit thickness it appears VERY thick as if the rod big end was machined sometime in the past for a thicker bearing material and the shop left behind so old Babbit.
 These Babbit type bearing engines didn't have what is referred to as 10, 20 or 30 undersize bearings. The crankshaft journals were machined smaller that original and a Babbit was made into the rods to fit. I plan to follow this to see how the repair is completed. 
 
Gary Parsons
I have tried to get better pics to show the thin layer of babbit but not that easy. Here is another used rod and cap showing a thin layer of babbit and a lot more rod between the babbit and the rod bolt. This rod also measures 2.115.I would suggest that you not use the original rods you had in the car when you got it.Pete
When crankshafts are turned undersize the babbit gets thicker.
CORDially MIke
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.








