Use a generic key blank to perfect the blank before you cut an Auburn script key. I do not know who made the Auburn script key blanks but they were also used on 36-7 Cord so maybe post a wanted there.
You might want to contact Jarvis; he has hundreds of pounds of keys and locks and is very knowledgeable; he is located in Washington state. Use the address below.
 
ModelTBug@aol.com
Thanks for your reply. My handle does not appear to have removable lock cylinder . Did these door handles have lock cylinders that were pressed into the handle and are not removable?
 
My problem is a lack of understanding for the original design (plus a general lack of knowledge about door handle locks in particular). As you can tell, I need help on an elementary level.
Thanks for your reply. My handle does not appear to have removable lock cylinder . Did these door handles have lock cylinders that were pressed into the handle and are not removable?
 
My problem is a lack of understanding for the original design (plus a general lack of knowledge about door handle locks in particular). As you can tell, I need help on an elementary level.
MorningHere are pics of an Auburn handle showing the small hole thru which you must depress a retaining ring which holds the lock cylinder in place; a paper clip works well.The other pics show several lock cylinders with and without script keys, all yale except the very right key(Chicago).The LH cylinder and non-script key would work for you;UNLESS you have an after market door handle. As a general rule aftermarket handles do not have the small peak above the cylinder hole. If you want a pic I can get 1.My 2 centsPete Kelly
Pete...
 
First of all, thank you for your effort to help me out! My door handle does have the small hole exactly where you suggested that it would be... a local locksmith said the hole was simply for drainage. I will fiddle with this tomorrow as you suggested and let you know what the outcome is.
 
Again, thanks!
Sadly your locksmith is wrong. If you look at the key cylinders Pete offered up for pics you see the small piece of metal near the bottom of the cylinders 1, 3 and I think 5.Well when you push in a piece of wire into the "DRAIN HOLE"... That piece moves up into the cylinder. Then you just pull the cylinder out of the handle. If it wont budge try some Aerokroil or PB Blaster to loosen the spring. They do come out ez.
 
 
Gary Parsons
Here is my handle and, sure enough, the "drain hole" seems to be in the same position as the handle in the previous photo. I'm able to press a thin rod about 5/8th of an inch into that hole. I don't feel anything except what seems to be end of the hole. Question: are there two parts to this handle; first is copper colored handle and second is the silver colored end that fits into the door lock mechanism. Is the silver end suppose to turn inside the door handle?
Please note the position of the spring loaded retaining tongue in the pics relative to the key.The lock cylinder must be turned so the paper clip pushes on the center of the tongue; you can feel the spring tension as you depress the tongue. Once depressed and held in(down) rotate the cylinder back and forth slightly with a key while pulling and it should come out. 
I posted the above reply before I saw your last post.
The door handle operates by locking the handle in the escutcheon in the door so the whole handle will not turn.
Someone seems to have modified your handle.
1-the handle should be 1 piece
2-trying to remove the cylinder should require inserting the paper clip not much more than 1/8". I suspect your handle is just a dummy
I will look tomorrow and see if I have a repairable handle or a junk 1 so you can see how it works.
Time to ask if anyone has a good handle for sale.
Pete
Thanks Pete...
I think you might be right... I've put lock fluid on and there is no movement beyond the what I can feel by inserting the key.
Trying to clarify the situation but may be going the other way.I do not know if Yale and Basco both made handles for Auburn in 31-3(Randy would know this)3 locking handles; pics in orderHandle #1- bottom right-1 key; pics 2-4, could be Auburn-handle chromed with lock cylinder in place-bad idea-lock cylinder stuck, Faith Chicago key, handle junkHandle #2-center handle-1 key with ring, pics 5-7-after market, bezel in bad pot metal-lock cyl stuck, locked position alows handle to spin freelyHandle #3-LH handle in first pic,-2 keys Basco;pics 8-12, could be Auburn-shows bezel with insert which locks the handle-pics show tongue in the locked and unlocked positions-pin hole near the tongue may be used to remove the lock cyl(don't know)-operates properly-hole in the usual place to remove lock cyl is just a depression
Hi Pete...
It seems that my door handle has been modified and I am in the process of disassembling it to see exactly what has been done. Thank you for all the pictures. Stay tuned.
Don
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.



















