In contrast, here are another couple of cars where the pointy part of the top of the rubber grommet faces toward the center of the car. So what is right? I realize that original speedsters can be restored and have their reassembly done incorrectly, so its certainly possible that the 4 original cars I quoted above in earlier post, were fitted incorrectly after restoration. This leads me to considering looking at early original photos of auburn 851/852 cars.......preferably factory photos.....but I don't really have any. I do however have a photo from this forum, from the early 1940's which is a reference....see next postregards Jerome
So here is a photo which was posted on this same forum by johnmereness, from original photos taken in 1942 (thanks so much John, they are incredible photos). It shows the pointy bit (at the top of the rubber grommet) closest to the outside of the car. So what placement is correct? Gurus in the club.....I'd certainly appreciate your opinion.....that being said, I'd love to see early photographic evidence to support your opinion. This photo from 1942 certainly appears to be supporting the placement of the pointy bit toward the outside of the car. Many many thanks Jerome
Its great to see you are determined to do it right the first time. Personally I would go with the early 1942 picture but... I also noticed the pics shows several different reproduction grommets.
 
 
Gary Parsons
Thanks Gary. Yes there are reproduction grommets. The most common current supplier I know of is Metro Moulded Parts, but their rubber base which glues to the car body appears to be too big in my opinion. Anyway, my grommets are probably from the 1970's and are smaller than the Metro Moulded Parts grommets which have been fitted to the red car in the previous post. Regardless of the size of the grommet, the pointy part at the top of the grommet must point either toward the center of the car or toward the outside edge of the car.......that is the question as we both know.
 
Re the positioning of the grommet, I am inclined to go with the positioning as shown in 1942 picture (with pointy bit closest to outside of the car), but I hesitate because the sage green car I referenced above (alongside the red car) is owned by fellow ACD club member Curt Shultze, and he is someone that is a recognized expert and someone I have a lot of respect for as an authority on these vehicles, and he has it with the pointy part towards the center of the car......that's why I hesitate, and am asking the question.
 
Placing these grommets involves gluing them against the paintwork.....I do not want to make a mistake as I will ruin the paint if I need to correct it. I have seen some cars put screws into them to hold them against the paint......looks awful and of course is not original
The factory was pretty nut and bolt consistent - they may have been a small manufacture but they were pretty innovative and had mass production and .... on the brain.
 
I would go with the 1942 photos.
Well here is another early photo of a speedster that shows the pointy bit towards the outside of the car. It is from the ACD online library and shows 1930's movie star Robert Donat. If you have early photos of 851 or 852 speedsters that show the rear of the car, and the positioning of the rear rubber bumper arm grommets that would be great to see. Obviously various members of the club have formed opinions. I think it will be great to see what various early period photos show us. It may be there is variation in cars....where some are done with the pointy bit outwards (most common at this stage), and some cars have the pointy bit closest to the center of the car. Lets see various photos to see what they tell us.
Nice picture with the spare tire but... Would this mount have been factory installed or dealer aftermarket? If aftermarket then one may want to see more factory original cars. At this point I do not think the factory would be switching mid assembly line installation of these bumper grommets. I'm not even close to being an authority on the Auburn cars.
 
 
Gary Parsons
Gary
Excellent comments. I agree that the car showing Robert Donat has a number of modifications (white steering wheel and additional rear spare tire). I do believe that changing the rubber grommets on the Robert Donat car is unlikely to be one of them unless the car was in a rear accident.....so its an interesting photo to see and another part of the puzzle. I am yet to see an early photo showing the rubber bumper arm grommets with the pointy bit at the top closest to the center of the car. That is not to say they don't exist, but hopefully other club members will contribute here.
 
Kind regards J
You must take something else into consideration when fitting these grommets. The holes in the fender you are trying to cover up were all hand cut and may not have been cut the same. Mine do not match from one fender to the other. I'm sure they would place the grommet to cover the hole possibly requiring a different placement of the grommet from one car to the next. So I'm not sure you can say one way is correct and another is not .
CORDiallyMike
The frame rails were not always the same length .
White steering wheels were an option, P/N F10445
Curt. Thanks for telling me about the white steering wheel as an option. I appreciate your expertise and as always, learn from you.
 
Are you of the opinion that the placement of the rubber grommets in the rear could have the pointy bit placed either way, and that original Auburn 851/852 Speedsters were delivered with placement both ways?
Thanks Curt for sharing your opinion. I along with (I'm sure) all other members reading this appreciate your comment.
I have one other question for you if you don't mind.
I believe the size of the rubber grommets between the front and back vary in size (at least mine do). Do the larger grommets fit on the back of the car?
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.









