Possibly battery is no good. You can have six volts but a bad cell.
Are your cable. Like 00 and not like 12v car battery size. I bought a car which had small cable and eventually it would spin the motor. Changed to large cable and walla.
Make sure Bendix is not locked on to ring gear too.
Hmmm...On the topic of batteries, I've noticed mine not holding a charge very long and when traveling with the lights on I come home to a very weak battery, even after only about 1/2 hour drive.
Any recommendations on a replacement battery? I've read about using 2 Optima 6V batteries in parallel. I'm not sure what that means. Thanks!
Before you get too concerned about changes, have you had the battery load tested? Almost any parts store can do that for you free. Have the battery fully charged before having it tested. Might save you a bunch of needless work.
CORDiallyMike
Well, new Optima battery installed and nothing changes. Startix still clicks with the button pushed or when toggle is moved down to STX.
I'm at a loss.
Like I said earlier, it seemed to fade to this point, with the last few starts delayed and becoming weaker, but at least it did crank.
Any more ideas now that the battery has been ruled out?
Check the draw when the startix button is pushed.
Bypass the startix
Check the condition of the ends of the cables
Pete
Thanks Pete.
I'm sorry to ask, but could you be more specific? How & where do I check the draw?
To bypass the startix, do I connect the battery directly to the starter?
The condition of the cables...Corrosion, or ?
Thanks for your help!
To check battery draw you need a meter that lays over the main battery cable. Then you try to start the engine. When the engine cranks or wont crank the meter shows the amp draw thru the cable. The meters I'm most familar with are round and the back part is like U channel that slips over the cable.
 
 
Gary Parsons
Buy a small amp gauge that just is held up to the heavy wire leading to the starter. It should show several hundred amps when the button is pushed. If it shows amperage then make sure the bendix is not jambed in the ring gear. If no amperage check the wires all the way from the battery to the starter and the battery to ground for corrosion or a poor connection. Also check the wire from the frame to the engine bolt. It could be a bad starter with high or no amperage draw.
Can you turn the engine over by rocking the car in gear; if the bendix is stuck that could release it?
Let us know how you make out.
Pete
Thanks again Pete.
I've tried a couple of things now. My amp gauge (Fluke) showed nothing with the ING on, (-) probe on the out wire to the starter and the button depressed.
Also I tried bypassing the Startix by putting battery power (-) directly to the starter. Nothing but sparks.
I tried rocking the car in gear but it didn't seem to turn the engine at all.
I SO appreciate your guidance!
Ken
You should not have seen nothing but sparks when you connected the battery directly to the starter.Now it sounds like your starter has failed. Remove the starter and find a good mom n pop starter re-builder that can check this out.
 
 
Gary Parsons
Ken
Give me a call on the number I sent you under the private messages.
Pete
Before you remove the starter take the clutch inspection
cover off under the car and make sure the Bendix drive is not stuck into the flywheel gear. A quick and cheap way to check for too much draw is to see if the wire gets very hot If so there is too much resistance in whatever the wire feeds. If the cable too the starter gets very hot, for example,it would tell you the starter is trying to work but for some reason can't.
CORDiallyMike
I tried "starting" it from the Startix button this morning and found the cable to the starter and that end of the starter getting warmer and warmer.
Bad or stuck starter?
The connections are all tight with no corrosion.
Best way to check this would be? Mike's idea sounds reasonable if I can get under the car. It currently sits stuck half way up my lift ramp.
By "clutch plate" and "Bendix" is this referring to the starter? Or is there a plate under the actual clutch?
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
