A spark arrestor will be good but the more important question is to correct the reason for the back fire.
CORDiallyMike
More on the 8-98A fire:
1) Attached, if I can do it, an enlargement of the factory photo of the 8-98 carburetor. Can just see something in the mouth of the carb air intake, I'm presuming a flame arrestor. Missing from my car.
2) Thanks to Pete Kelly for posting the air cleaner pic.
3) Studying the 8-98 and 8-100 parts books, 8-98 does not mention an air cleaner, 8-100 lists one (part #J10052), but does not illustrate it. Probably like Pete's photo, and if so Bob Esten's car likely has a post-production retrofit. But there were two carbs for 8-100, Schebler, which was replaced by Stromberg.
4) An old Chilton's shows Schebler model T (8-98) and Stromberg model URO-2 (8-100). They look to be similar shapes, so might take the same air cleaner. [Re: Neil Ziff's 8-95: Chilton's says it used Schebler model U and Schebler model S-Duplex. From the book's drawings, they might not orient the same as the later Schebler, but hard to tell much from drawings.]
4) I found a reproduction air cleaner on ebay (rather expensive), have ordered it, but it's not here yet, so haven't tried it. Wish me good fortune!
5) Mike's point: Exactly rightÔÇöwhy did it backfire thru the carb? Has never happened before, but I'd just as soon it didn't happen again.
I used a fair amount of choke that day (it didn't start right away) and I always use the spark control, which I've presumed retards the spark, that's what happens with other cars I know that have spark controls. BTW: the owner's manual says very little about the spark control, essentially nothing with respect to starting the car.
My logic (which might not be correct) says that a backfire thru the carburetor would happen when the spark is too far advanced, not when it's retarded. I might have flooded the engine a bit from cranking on the starter, tho I've cranked it a lot more in past case, but that wouldn't by itself produce a backfire, if the ignition is right. But how could the spark be too far advanced from using the spark control? Unless, on the 8-98 it is a manual advance, rather than a retard for starting? Can that be the case?
neteThanks for inquiring. I've been pondering the whole matter, here's 'progress' to date.I got the repro air cleaner, bought from 'samsonized' who posted parts for sale on the forum. It's nicely made. The seller assured me that it would fit the '32 8-100, and we both agree that the parts book for '31 8-98 (my car) lists no air cleaner, so the question is: Does the '32 cleaner fit the '31 car? Both use Schebler carbs, at least the early 8-100s do.Samsonized's air cleaner is a bit different shape from the one on Bob Esten's car (Pete's photo, this thread). The new cleaner has inner and outer shells, both perforated, no way to put steel wool, or whatever is in Esten's air cleaner (Pete's photo), inside. But the big problem: There is very little space on my car between carb air intake and the steering box (see photo). The photo angle makes it a bit hard to see, but at its closest, a ┬╝ inch drill is a pressure fit between carb air intake and steering box. Then, the 'snout' of Simonized's air cleaner is shorter and has a different angle contour than the one on Esten's car (compare 2nd photo with Pete's photo), and the cleaner might be a little bigger. No way I can get the new air cleaner on the carb without removing the carb (which I don't want to do for more than one reason) and I'm pretty sure I couldn't get the carb back on with the air cleaner installed. Also, Esten's air cleaner might be in two parts, so one could remove the box without removing the shaft from the carb (to service the steering box, for example), but that's not likely to matter much for the fit problem. What to do? The fit would be possible if the carb were an inch or so higher, but I can't see any spacer or any way that the height of the carb could be changed. Note that from the linkages and so forth, the two Schebler carbs seem the same, so I've ruled out an incorrect carb on my car.. Fit would be possible, also, if the steering box were just a bit more to the rear or lower, but that can't vary, can it? I suppose I can't rule our some restoration mistake from the previous owner's shop. So at the moment, I'm stumped. Suggestions?
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.








