Roger, adjust your toe-in to no more than 1/8. Use about 4 degrees caster.
Radials will not fix tour problem.
I agree with Curt - it is an alignment issue and radial tires will not solve the problem.
 
And, I would suspect the tie rod needed replaced as some alignment issue tore it up.
 
You would have loved seeing our 851 Phaeton on a Hunter alignment rack being done via computer at a local fellows who sets up race cars (and Hunter even had the specs for the Auburn in their IT program).
I would also check if there is lube inside the steering box
Oftener than not the oil has all dripped out and this it can make steering looser.
Fill it with regular no2 grease
I use the same as Curt suggests. It is called pourable grease and does not channel like grease. Give yourself plenty of time to put it in though.
Cordially Mike
The bottle says Steering Box Lube, A semi Fluid Extreme Pressure Grease. There is no part no. on the bottle.
Cordially Mike
I am also using Penrite Steering Box Lube (and have for years now) - great stuff. Mike is right - do not be in a hurry when installing such.
 
Roger, I do agree with you to some extent - you can rebuild the whole front end, incl. shock, steering box, perfectly balance the tires, and ... and get the problem a whole lot better (aka why you possibly experienced success with the adjustment of the Hartford shocks on your Jaguar) - but it is just a band-aid at best if alignment is the issue.
 
I will match the handling of our 1935 Auburn to anything made pre 1955 and most anything without power steering - it is worth the effort to get it truly right. Also, I hear the same from several 810 812 Cord owners.
I to had the front end wobble, that didn't show up till a tire change
My biggest fault was a worn king pin
I rebuilt the king pins, made sure tie rods were snug and used 2 deg
Caster
I had a professional alignment the car drives great
No shake, pull and can be handled with one hand while driving
A close inspection showed the faults
Greg
Greg is absolutely spot on. Worn King pins are notorious for front wheel shimmy. Usually when you hit a bump in the road, that sets it off. Slow down and it goes away until the next bump. I would seriously consider addressing this issue.
 
Joel
I bought my 1932 Auburn, (restored by Bill Bools), and the chassis and front suspension had been completely and properly rebuilt except there were no caster wedge plates installed. The car would produce the described wheel shimmy occasionally. I found a source for new 2 degree wedge plates, installed a set and never again had a single shimmy occurrence no matter how big a chuck hole I hit. I had seen a broken set of factory wedge plates and these new ones were identical except longer (I cut them off a little). These plates are made for race chassis applications and are aluminum like the originals.
 
Here is the information on them:
 
Brand: Competition Engineering Inc.
Item#: C7025 Wedge Plates 2 degree. Two per package.
Special order through O'Reilly's Auto Parts
I think the price was around $30.00
 
These have a hole in the center for the axel to spring alignment pin and are corregated so they can be stacked if more than 2 degrees of caster is needed. The 1932 factory bulletins call for 2 degrees of positive caster, but I think the later models may call for 4 degrees. I would try 2 degrees and only go the 4 degrees if necessary. Be sure to install them with the thick end of the wedge plates toward the rear (positive caster) otherwise you will be creating negative caster and make the problem worse.
 
Steve Stevens
The like style wedges are also available thru your local
NAPA store. They have a complete catalog for just alignment
Products. Usually available overnight
Greg
A lot of people used to get their parts from salvage yards overnight too.
Cordially Mike
Microwave works too. But not too long or your wife WILL find out. I used the oven to cure VHT paint once when Joan wasn't home. Like I said, only once!
Cordially Mike
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
