Curt, Are you going to send the snowballs to him in CA.
CORDially Mike
Did you measure the heads and make sure they are commom hardware bolts.
Cordially Mike
Got them all off. What I did was to break the lock washers, which gave a little more room to push the bolts heads back away from the mounting plates. This gave me just enough edge to grab with some vise-grips without doing much damage. I ran the die over the bolts and soaked them with PB Blaster daily. Then I heated them up red-hot. Curt - I gave the snowball idea some consideration, but it's 2 hours to the nearest mountain and my kids' slushie machine is broken. Luckily they all came off without that extra ingredient.
 
Pretty much ready to pull now. Don't be shy with suggestions - they really help. Especially when you've never done this before. Will send another pic when out.
 
http://i745.photobucket.com/albums/xx99/NZiff/20141217_145948.jpg
Neal, I figured your location out with Mikes help. No snow balls in sunny CA.
 
We have a 30 year old wood stove in the basement that I needed to remove the door to replenish the insulation rope. The bolts and nuts were so rusty that the hex's rounded off and the area was too tight for a vice grip or a hacksaw. I brought my little 'junk-yard' acetylene torch down, went out side and got a snowball heated the bolt and nut up cherry red and promptly applied said snowball. The nuts spun right off. This works MUCH better than just heating the nut.
I presume you are going to remove the trans. before pulling the motor. I also remove the heavy stuff, exhaust manifold, intake manifold, generator and fan before pulling. I don't know how other people do it but I remove the cyl. head and mount a steel plate to the top of the block, with provisions for a hook, with the head bolts and pull it that way. The plate is centrally located on top of the block and keeps things nice and straight when lifting. I'm sure other people have other opinions so listen to them all and take your choice.
Cordially Mike
Neil,
I have pulled engines both with the trans and without for the early Auburns.
Its easier, as Mike suggested, to pull without trans. Remove floor boards, disconnect driveshaft, remove trans mounting bolts, pull back and remove along with the emergency brake.
 
Joel
Once again - thanks for the comments. I was about to try to leave the trans in the car and separate at the clutch housing. Switching gears now (pardon the pun). Having not done this before, I'm flying blind without all the help. I like the idea of the leveler - going to check it out at Harbor Freight. Hopefully the next post you see is after the extraction.
 
Happy Holidays,
Neal
 
http://i745.photobucket.com/albums/xx99/NZiff/20141219_094716.jpg
http://i745.photobucket.com/albums/xx99/NZiff/20141219_094556.jpg
If you use an engine leveler, be sure the nut on the end of the crank handle rod (opposite end of handle) is well secured. I have seen units that have just a cotter key holding the nut on. A cotter key can work fine if it is a good quality key and everything is well lubricated. If the nut comes free, you can unscrew the rod from the nut while trying to tilt the engine and then everything will fall. Just something to check. There are good units and others that you can get by with. A little lubrication on the treaded rod and the traveling block helps a lot.
Love the pictures of your car. Happy Holidays!
Is this what you guys are referring to as an engine leveler?
Ones like this are what I'm use to.
I use load leveler as well. Very handy. I use a Arcon CL 1250 that I got from Northern Tool for $45.00. Probably more than Harbor Freight but worth the money. Just type in Arcon CL 1250 and take a look. More adjustable and versatile than most. Just used it to remove Marmon 16 heads.
Cordially Mike
Hi Neal,
I have to agree with both Joel & Mike-- remove everything you can easily while the motor is still in the car. Carbs, Manifold, distributors, wire covers, generator, starters etc have a horrible habit of hanging up in ways you didn't think possible. This will damage the accessory itself, damage what it hangs up on or, normally, both. Also, if you have doubts about how to put everything back together, take LOTS of pictures.
 
Hopefully, we will see you at next years WCM with your car once again!
Curt Warner
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
