Did you put a little oil in each cylinder.
Just a thought.
John
Operation #4.
Pull #1 plug.
Remove dist. cap.
Turn the engine over with your thumb over the hole.
Note the position of the rotor when the compression stroke is on top.
I'll bet it is 180 off.
When you say that "the rotor is in line with the number one cylinder" you mean that the rotor is lined up to the bottom of the CAP at the number one cylinder firing position right? Also,are the spark plug wire covers installed?
Be certain that the distributor itself moves freely for both advance and retarded as limited by the bolt and slot on the passenger side of the distributor's base.
Better yet,pull out the cotter pin and steering wheel linkage for now and manually retarded the distributor so that you KNOW it is where you want it to fire and try that.
 
When you mentioned that the distributor had been rebuilt, how far was it taken apart? I ask because one can get the rotor position"off" from the lower gear and slot.(seen this a hundred times.
I will be around all day, and can answer questions if you wish to call me. I will PM you my number.
Andy
Is the valve timing off? If the valves are not in sync. with the pistons you could feel a pop, but the piston is not at TDC. Maybe some one messed with the timing chain and didn't get it right. I agree with Curt thought, it is probably firing on the exhaust stroke. I have done that myself and swore it was not 180 out, but I was wrong. To satisfy yourself, change the firing 180 and see what happens.
Cordially Mike
http://i1159.photobucket.com/albums/p633/ivor6/scan0010.jpg
 
Hello Nick,
i sent Pm not sure if you got it. If you have the distributor cap with the leads out the side you need to use the sketch above as a guide as the leads dont come out in the same order as the vertical type caps, you can easily get the wrong firing order if you just work around the direction of rotation as you would with a vertical lead type cap.
Thanks Ivor
My rotation is clockwise on the 3 Auburn.
Ivor,
Thanks for sending the correct rotation for my 1930
My 1930 Auburn rotation is Clockwise and my 1933 Auburn rotation is Counter clockwise.
I tried uploading the schematic that Ivor sent that showed this but had problems uploading image.
 
By the way: I am still working the issue
You said in your first post that you have fuel and spark. That leaves only one component, compression / vacuum. Run a compression check on all cylinders and your problem will be obvious.
Steve Stevens
 
PS: On a properly operating updraft carburetor, if you choke it and crank it for several seconds without it starting, you will have gas running out on the floor. If not, you have a stopped up carburetor or no compression / vacuum.
According to my info. the only Auburn distributors that turns clockwise, viewed from the dist. cap end, is the Big Eight used in the 120-125, the L-29 Cord, and the V12. All the other engines dist. turn counterclockwise. I am only talking 1929 to 1936. That's according to my Tune Up Charts.
Cordially Mike
That is my thought Mike. The AutoLite distributors have an arrow on top of the shaft where the felt is indicating direction. I don't know about the Delco's
It is easy to see when the engine is turning over and watch the rotor.
 
Years ago, I had a 28 Dodge Victory 6. My father-in-law and I were working on the starter and it somehow turned the engine over in the opposite direction. It had something to do with the poliarity in the field coils vs armature. I do remember having two identical starters that spun in opposite directions.
Do you have quality spark (not just spark) ?
Do you have compression (sounds like you may have in 1, but how about 2-8 - it does not need to be anywhere even close to perfect, but you still need it).
Have you asked why this Auburn fell off the road in the first place (ex. did someone prior to you get the valve timing wrong).
Try some starting fluid as carb may be too far off - be careful with the stuff as bad things happen to people who do not know how to use it properly or actually do not use it properly.
 
And, I would start from scratch on the timing.
Curt did they still have the silent starter in 28, If they did I suppose the starter could be made to run in reverse
K Clark
To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.
